Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 22
-
24th June 2011, 06:00 PM #1Senior Member
- Join Date
- Jul 2009
- Location
- queensland
- Posts
- 129
Oregon for work bench base frame ??
Just a quick question for the panel.
I am planning to build a decent work bench in the near future, or start to build, would be more appropriate.
The basic design will be a roubo style with leg vices and sliding deadman with removable leg vise chop. Along with a veritas or some type of twin screw vice as an end.
All the joinery for the base will be M&T, either draw bored or wedged Tennon.
I am in the timber gathering phase and have access to some 200x 125 oregon, which i will mill to the largest possible square section.
Do you think this would be suitable for the base of my bench? I intend to be using some hard wood for the top which would be around the 100 mm mark, thick. Not sure which timber would be best suited for the top though. Suggestions welcome!!
Thanks
Skippy
P.S. thanks to everyone who puts thier work in the WIP spotlight. I have learnt heaps
-
24th June 2011 06:00 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th June 2011, 06:04 PM #2More Firewood
- Join Date
- May 2008
- Location
- Laguna
- Age
- 69
- Posts
- 60
Hi
I used recycled Oregon for most of my bench - including the
https://www.woodworkforums.com/f213/r...59/#post976154
After two years I have no regrets and it is certainly heavy enough.
Andrew
-
24th June 2011, 06:19 PM #3Senior Member
- Join Date
- Jul 2009
- Location
- queensland
- Posts
- 129
Do you find the top dings easily? I ask because i am a bit wayward with the hammer every now and then LOL
-
24th June 2011, 07:09 PM #4More Firewood
- Join Date
- May 2008
- Location
- Laguna
- Age
- 69
- Posts
- 60
Hi
I use a wooden mallet with a big head rather than a hammer. Also I try not to do steel work on the bench as residual iron filings can leave nasty black stains on wood. And I rarely use nails.
So in answer, a hammer will ding the bench. But I have not found it a problem.
Andrew
-
24th June 2011, 08:11 PM #5
Alastair built his bench using Oregon timber for a base here
And it is as solid as!regards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
24th June 2011, 09:13 PM #6Senior Member
- Join Date
- Jul 2009
- Location
- queensland
- Posts
- 129
Thanks sawdust
That base look pretty solid alright. I like the idea of the oregon for a couple of reasons.
It is supposed to be lineally quite strong
it should be easier on the chisels etc to work than hard wood.
Negatives that i can see is that it wont be as heavy as the hard woods. However, given the end dimensions are going to be around 100 x 100 i dont think it will be a light weight either.
I am a bit concerned about splitting while draw boring
Skippy
-
25th June 2011, 01:00 PM #7Senior Member
- Join Date
- Jun 2010
- Location
- Canberra
- Posts
- 195
I wish I could give you the oregon posts in my carport to use. They're taking up space! I collected them long after I started my own bench, otherwise I would probably have used them.
-
25th June 2011, 01:08 PM #8Senior Member
- Join Date
- Jul 2009
- Location
- queensland
- Posts
- 129
I wish i was able to get em. Only as a kind gesture to help clear your carport you understand..
-
25th June 2011, 01:29 PM #9
Oregon works for me. Top gets a few marks but it's only a workbench after all
you can see my bench in the link below if you dig a bit, but I think you already saw it
-
25th June 2011, 02:05 PM #10New Member
- Join Date
- Oct 2007
- Location
- Nebraska, USA
- Posts
- 9
In the US, we have a State named Oregon, and they have a lot of wood there, but I've never heard of a wood named Oregon. Is it a common name for something else?
-
25th June 2011, 02:08 PM #11
-
25th June 2011, 02:47 PM #12New Member
- Join Date
- Oct 2007
- Location
- Nebraska, USA
- Posts
- 9
Right, makes sense. Lot of Fir in Oregon. Thanks.
-
25th June 2011, 03:23 PM #13Senior Member
- Join Date
- Jul 2009
- Location
- queensland
- Posts
- 129
Well it seems the Oregon will be fine for the base. Any suggections for the top?
It will be hard wood i have a mill down the road who kiln dry timber as well. I am also happy to use recycled stuff as well, its just that having the mill down the road, if i can use new, i will. I will be flattening the Top by hand plane !!!
-
25th June 2011, 03:41 PM #14GOLD MEMBER
- Join Date
- Apr 2011
- Location
- McBride BC Canada
- Posts
- 3,543
Sorry
Pffffssstttt. Thanks for playing.
I am a retired PhD dendrologist. "Oregon" is a bastard term for Pinus radiata which was shipped in a massive seed exchange for Eucalyptus sp., back in the 1920's or 1930's.
The common but useless name was Monterey Pine. (did I spell that right?)
It is plain old 'pine' wood to us north of the equator. Douglas-fir, (Pseudotsuga menziesii) it sure as dang is not. You should be happy. Doug-fir is a terrible timber for splits and brash shattering. Nightmare to paint for the spiral thickening in the S2 layer of the cell walls. Unless you have some death wish, stay away from that stuff.
Properly dried, "oregon" will do fine for benches. I do stone-cut printing. I have MASSIVE benches for polishing one stone slab against another with fine sand/abrasive & water.
Just as soon as I can score an old telegraph pole, I will replace the bench legs.
-
25th June 2011, 03:49 PM #15
Similar Threads
-
What to do with a broken Base Bench Plane.
By Scribbly Gum in forum HAND TOOLS - UNPOWEREDReplies: 7Last Post: 30th May 2010, 11:32 PM -
Sontax 100mm Swivel base Bench vice
By MelbMan in forum PRODUCT REVIEWSReplies: 2Last Post: 14th October 2009, 03:46 PM -
oregon ok for work bench ?
By Zed in forum THE WORK BENCHReplies: 6Last Post: 15th January 2004, 04:22 PM