Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
18th August 2014, 11:38 AM #1Senior Member
- Join Date
- Aug 2010
- Location
- Wisconsin, USA
- Posts
- 151
Help with making my first saw handle
I'm attempting to make my first saw handle (tote) and I could use some assistance. I'm almost to the point where I need to cut the slot for the blade to slide into. I'm not sure what the best way to go about doing that is. I patterned the tote after an old lamb's tongue model (the saw I'm putting it onto is a Taylor Brothers). I haven't worked up enough nerve to carve in the lamb's tongue yet. Any suggestions there would be appreciated as well. Just one slip will ruin hours of work I've put into it so far.
-
18th August 2014 11:38 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
18th August 2014, 01:09 PM #2SENIOR MEMBER
- Join Date
- Dec 2005
- Location
- Sydney
- Age
- 79
- Posts
- 647
I assume you have had a look at the saw making sub-forum https://www.woodworkforums.com/f278. In there you find a plethora of info for just your needs
Cheers
Peter
-
18th August 2014, 01:39 PM #3
Cutting the blade slot is a bit nerve wracking, I just scribe a line from both sides with a marking gauge to get the center line, then with a saw that has a kerf about the thickness of the plate you are using, cut all the way around, but only go about 1/8" deep, then gradually deepen the cut, and keep rotating the work as you gradually cut deeper. If you aren't confident, then try a practice piece.
Also, you should cut the slot before you do any shaping, so you have square sides to reference from.
The other techniques involve clamping a saw plate to a flat surface, and, Stewie has a neat method using slitting saw blades..
Ray
PS.. Nearly forgot.. I did a write up on this a while back... http://www.backsaw.net/index.php?opt...=58&Itemid=102
-
18th August 2014, 02:01 PM #4
My couple of attempts have been with very thick stock. If the slit is a bit off centre or not straight it does not matter because you can remove the evidence as you thin the handle down.
-
18th August 2014, 11:56 PM #5
Just for future reference the saw slot is one of the first things I do .
Why because it's the most critical .
If u get it out of line there's no easy fix .
So I like to do it first once that's out of the way the rest is still important but not as critical
Ray's method works well but is a skill .
Another approach is to lay the saw you are going to use to cut the saw kerf stacked up on horizontal blocks to the centre height of your new tote and clamp it down then push and pull the tore across the teeth of the horizontal saw in a way you are moving the material not the saw .
This approach works well ,a bit slow but still good .
Another approach like mine now is to use a slitting saw in a router( note u must be able to slow your router right down)table but this takes a bit of equipment and u have to know what your doing .
I would not recommend this if your not sure of the setup and what is required .
Ps we want pics it's the only reason we come here
Matt
-
19th August 2014, 08:57 AM #6
I use the method RayG describes. It takes care & you need a goodly selection of saws (which run true!) so that you can match the gauge of saw you are bedding. The kerf can be just a little bigger than the plate thickness, as long as it will tighten up ok without undue force on your saw nuts. It's important to get a straight slot (i.e. all in one plane), because if it's curved, you will get a bow in the heel end of the saw when you tighten the bolts, which is unsightly, even if it's not severe enough to affect saw usage. The deeper the slot, the harder it is to get perfect.
Using a slitting saw of the right thickness helps a lot if you aren't confident sawing by hand. You can only cut about an inch deep, max, with a 3" blade because of the large boss. I haven't Simplicity's courage, my router can't be slowed down enough for me, so I use it in the drill-press - about 800rpm is plenty! As he says, if you aren't confident, don't do it, but if you do, think the process through & present the work in a way that if it catches (which happens easily, since slitting saw blades are for metal & have no set), you can restrain it without getting a finger or two dragged over the saw. You will still need to finish the kerf by hand on most handles. You also may need to deepen & round the back of the kerf depending on handle design & saw. To do this, I've made several small saws from scrap. These have teeth filed to cut on the pull stroke, and a rounded end like a stair saw. They have no set, so they are slow-cutting, but they do the job. The only time I bother with the slitting saw is when I have a batch to cut - it's a pita to set up perfectly in the DP, & not worth the effort for a single handle....
Cheers,IW
-
19th August 2014, 10:59 AM #7Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi Ian. The issues you raised with a slitting blade to cut the slot for the saw blade fit to the handle are very true. You need to have the right set up with your router table before contemplating this method. In my case that involves the use of a Woodpecker Router Lift and the new model Triton TRA001 with its variable speed benefits. Speed control is critical element when using a slitting blade mounted to a router.
Stewie;
Similar Threads
-
Making up a 3 ball handle
By Michael G in forum METALWORK FORUMReplies: 12Last Post: 1st June 2014, 10:59 PM -
Cindy Drozda making a tool handle Youtube video
By Mobyturns in forum WOODTURNING - GENERALReplies: 3Last Post: 13th March 2014, 05:46 PM -
New Saw Handle
By planemaker in forum HAND TOOLS - UNPOWEREDReplies: 12Last Post: 17th January 2011, 10:19 AM -
help with making a hand plane handle
By mkat in forum WOODWORK - GENERALReplies: 6Last Post: 14th January 2009, 11:13 PM -
Bow Handle
By Don Mc. in forum BANDSAWN BOXESReplies: 6Last Post: 13th May 2007, 11:08 PM