Needs Pictures: 0
Results 31 to 45 of 62
-
3rd October 2014, 02:47 PM #31Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
3rd October 2014 02:47 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
3rd October 2014, 03:43 PM #32Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
To accurately describe how much fun it is to mortise these plane bodies out; "imagine watching a 3 legged tortoise compete in a 20k marathon, from the very start to when it crosses the finish line."
Stewie;
-
3rd October 2014, 04:01 PM #33
Would the tortoise have runners on
-
3rd October 2014, 04:24 PM #34
-
3rd October 2014, 11:13 PM #35Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
No pain no gain Paul.
-
11th October 2014, 06:50 PM #36Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
11th October 2014, 10:34 PM #37GOLD MEMBER
- Join Date
- Apr 2012
- Location
- Sydney
- Posts
- 1,503
These seem to have a mush larger V section than the first plane.
What was the rationale behind that?
The surface of the V looks great. How did you finish it and keep it square?
-
12th October 2014, 01:52 AM #38Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi Hiroller.
The V sole is an important design feature of the plane. The sole needs to remain in full contact with the flat surfaces of the 90* edge . By increasing the width of the sole I am also creating a greater contact surface area. That allows the plane to track more easily in parallel alignment to the boards corner edge.
Stewie;
-
20th October 2014, 05:47 PM #39Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
7th November 2014, 04:56 PM #40Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi all. As you will note from the attached photo's I am still making reasonable progress on the batch of box chamfer plane builds.
Still to complete. (in sequential order).
Cut the tines out on the wooden wedges;
Fit the outer brass keeper plates to the height adjuster;
Fit the brass sole plates on the bottom of the box;
Final shaping to the top of the plane bodies as well as complete the chamfering;
Fit strike buttons on the back end of the plane bodies;
Sharpen the irons up;
Test each plane and fine tune if required;
Apply 2 more coats of garnet shellac finish;
and the lastly- stamp the front end of the plane bodies with a makers mark;
Stewie;
-
10th November 2014, 09:23 AM #41SENIOR MEMBER
- Join Date
- Jul 2003
- Location
- Melbourne
- Age
- 53
- Posts
- 856
Fantastic work, I am assuming you sell some of the planes you make?
Do you ever make hollows/Rounds? I have always wanted a half set but have nver managed to find any at a descent price...
joez
-
10th November 2014, 10:29 AM #42
Great work Stewie. What motivated you to make these? Did you need to for some project or you just felt like doing it?
Cheers,
Rob
-
10th November 2014, 11:15 AM #43Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
10th November 2014, 11:52 AM #44Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
13th November 2014, 03:47 PM #45Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Similar Threads
-
Home Made Round Chamfer Plane Using A Stanley Smoothing Plane
By mike48 in forum HAND TOOLS - UNPOWEREDReplies: 3Last Post: 8th January 2013, 10:17 AM -
Chamfer plane
By Bob47 in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 6th December 2012, 11:26 AM -
First Home Made Plane- Chamfer
By Eldanos of KDM in forum HAND TOOLS - UNPOWEREDReplies: 18Last Post: 26th June 2009, 01:21 AM -
Mujingfang chamfer plane - HELP
By Luddite in forum HAND TOOLS - UNPOWEREDReplies: 22Last Post: 13th March 2009, 11:17 PM -
Chamfer Plane (and Pic #1)
By derekcohen in forum HAND TOOLS - UNPOWEREDReplies: 5Last Post: 24th August 2003, 09:51 PM