Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Braces & Bits
-
7th November 2014, 08:53 PM #1SENIOR MEMBER
- Join Date
- Jul 2010
- Location
- Canberra
- Posts
- 566
Braces & Bits
I am new to the world of Braces & Bits. I was given a couple by my father-in-law, that were used by his grandfather to construct their house. I have been restoring one, the other of which is going to be put in the scrap heap, sadly.
I have a few dumb questions about braces though.
Firstly, how is the handle installed? I can't spot glue marks or splits on any that I have seen indicating that the handle is placed on after the U shape is put in the metal shaft. Is the metal shaft bent after the handle has been put in place?
Thanks,
Craig
If nobody minds, as I start to learn more, I will start posting links to resources for finding out more.
-
7th November 2014 08:53 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
7th November 2014, 11:00 PM #2
-
7th November 2014, 11:01 PM #3
One of the dark secrets only the brace handle elves would know.
Regards
John
-
8th November 2014, 07:54 AM #4
interesting
for some reason the men's shed ends up with a lot of braces and bits
I was thinking of grabbing one or two and doing them upregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
8th November 2014, 10:02 AM #5Try not to be late, but never be early.
- Join Date
- Apr 2011
- Location
- Bakers Hill WA
- Age
- 75
- Posts
- 1,077
Hi Morbius,
The process of bending the frame after the handle was put on was patented in the USA by Harry S. Bartholemew on the 21 may 1861 (32347). Prior to this handles were either split and the two halves pinned together after installation, or as in the case with John S Fray sawn in half and the two halves elegantly held by two pewter bands.Long after Bartholomews method had been adopted by most manufacturers Fray were still using their pewter rings on some of their braces well into the 20th century.
An interesting resource is Sandy Moss www.sydnassloot.com
Closer to home the Tough company here in WA had a line of braces named Tough Minor (1946 - 1966) which utilised Bakelite handles, some of which were one piece put on before bending and some in two halves retained by two wraps of copper wire soldered.
Belonging to your father -in- laws grandfather they'd have to be pretty old can you see any ID on them?
Cheers,
Geoff.Last edited by Boringgeoff; 9th November 2014 at 08:57 AM. Reason: Punctuation.
-
8th November 2014, 10:11 PM #6SENIOR MEMBER
- Join Date
- Jul 2010
- Location
- Canberra
- Posts
- 566
Skinner Braces
Vann,
Weren't you looking into the history of the Skinner Manufacturing Co. at one point in time because you had some of their braces?
How did that go? Did you find out much?
Craig
-
8th November 2014, 10:14 PM #7SENIOR MEMBER
- Join Date
- Jul 2010
- Location
- Canberra
- Posts
- 566
Similar Threads
-
Hand braces
By gracoope in forum HAND TOOLS - UNPOWEREDReplies: 11Last Post: 1st January 2010, 08:14 PM -
Forstner bits for braces
By jmk89 in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 20th November 2009, 11:20 PM -
Braces ,Augers and Spoon bits
By Woodlee in forum HAND TOOLS - UNPOWEREDReplies: 6Last Post: 29th September 2007, 10:28 AM