Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Brace reamer bit?
-
12th July 2015, 03:21 PM #1
-
12th July 2015 03:21 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
12th July 2015, 07:42 PM #2GOLD MEMBER
- Join Date
- Jun 2014
- Location
- Seattle, Washington, USA
- Posts
- 1,857
I was literally using mine today for some round tenons. If you get an appropriately sized tenon cutter then these staked joints are really something... I takes multiple whacks with the mallet to unseat them. Bordering on a glueless joint if cut right.
I think you'll find a project for it eventually
Cheers,
Luke
-
12th July 2015, 07:52 PM #3Gatherer of rusty
planestools...
Proud member of the Wadkin Blockhead Club .
-
12th July 2015, 10:23 PM #4
Not sure I follow you Luke. Maybe a picture would help.
I can perhaps imagine it could be used to flare out one side of a hole that receives a round tenon so it can then be wedged in solidly, but as Vann says it would be a fairly extreme flare.
Franklin
-
13th July 2015, 12:06 AM #5GOLD MEMBER
- Join Date
- Jun 2014
- Location
- Seattle, Washington, USA
- Posts
- 1,857
I was cutting joints like these:
http://www.wonkeedonkeetools.co.uk/m...25DBSP-2-3.jpg
Only they were through tenons so that I could plane them flat on the other side.
Cheers,
Luke
-
13th July 2015, 02:32 AM #6
This is the first one I found...
http://www.ukworkshop.co.uk/forums/p...=Taper#p821195
The second one is smaller and came with a bunch of other brace bits.
I'm sure I've seen them in an old cattledog since - but can't think where, ATM.
Cheers, Vann.Gatherer of rustyplanestools...
Proud member of the Wadkin Blockhead Club .
-
13th July 2015, 07:41 AM #7
Yes Vann, here it is a Repaimans Deburring Reamer.
http://www.drill-bits.biz/braceshank-c-42_43.html
http://www.alvordpolk.com/catalog/dept.asp?id=91
Luke, Notwithstanding the drawing - which looks like the tip of a cricket stump to me, the rest of that article seems to show a very similar bit but with a shallower taper. The real trick would be to find a matching tenon cutter. http://www.wonkeedonkeetools.co.uk/s...ered-spoon-bit
Also my understanding of a spoon bit is one of these http://www.highlandwoodworking.com/m...spoonbits.aspx
http://www.mikestools.com/635-5000-T...Spoon-Bit.aspx
Cheers, Franklin
-
13th July 2015, 03:06 PM #8GOLD MEMBER
- Join Date
- Jun 2014
- Location
- Seattle, Washington, USA
- Posts
- 1,857
Yeah, I knew I wanted to make these style joints eventually, so I picked up a Veritas pair. I believe the reamer and tenon cutter, which is basically a glorified pencil sharpener, were around $70 all up. Throw in the $15 brace and it's not a bargain buy, but it's all you need for tapered, round tenon joints.
You may be able to make your own appropriately sized tenon cutter by using some wood, a plane blade, and the reamer itself? Sounds reasonably doable I think. Just gotta be super precise when reaming out the hole which will later define the tenon profile.
Cheers,
Luke
Similar Threads
-
Adjustable Reamer
By rogerbaker in forum METALWORK FORUMReplies: 10Last Post: 6th September 2013, 01:00 PM -
How do you Use a hand reamer
By rodm in forum METALWORK FORUMReplies: 11Last Post: 7th February 2010, 08:28 PM -
1MT Reamer
By Garell in forum METALWORK FORUMReplies: 3Last Post: 11th May 2006, 11:24 PM