Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: pva and bent laminations
-
28th September 2015, 08:28 AM #1New Member
- Join Date
- Aug 2015
- Location
- Toowoomba
- Posts
- 2
pva and bent laminations
Hi, pretty much gotta ask, is it good long term? I don't want a call in 2 years time about the things delaminating. Some sites I've looked at say no. But its cheap, spreads well and I hate urea glue. Just used Selleys exterior for the higher solids.
600mm high, 8 plies of 2.5mm tas oak, 260 and 300mm radii. I've had about 2-3mm springback and no discernible creep on the end grain.
Thanks for any thoughts.
-
28th September 2015 08:28 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th September 2015, 12:51 PM #2
Well I've done rockers on two rocking chairs and no problems 4 years on. High heat and moisture are the main threats so do a good quality finish.
SBPower corrupts, absolute power means we can run a hell of alot of power tools
-
29th September 2015, 03:19 PM #3
I did the long rails to an oval dining table in Layers of Radiata Pine then veneered them with Mahogany . That was easy 10 years ago , no problems with that.
-
29th September 2015, 09:49 PM #4Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
As long as you clamp it well and give it plenty of time to dry, PVA is perfectly fine.
-
1st October 2015, 04:50 PM #5
Titebond III is the go, its harder than standard PVA and will hold its stiffness better. use thin laminations and if possible more layers. I've done a little bit of lamination work and always used TBIII no problems. it's not even that expensive; carbatec sell it for about $40 for 3.8l (approx). I've had more success with bigger bends when I've pre wet the timbers to aid in the absorption of the glue into the wood fibres (i know glue generally sits on top but it seems to work for me). I'm always pretty generaous with the glue too- you dont want dry joints on bends.
Zed
-
3rd October 2015, 08:31 AM #6rrich Guest
I've used TBIII on white oak bent laminations. The only things that I can add are too many clamps and leave it in clamps for a day or so.
-
4th October 2015, 03:35 PM #7GOLD MEMBER
- Join Date
- May 2015
- Location
- Brisbane
- Posts
- 1,148
35 years ago as an apprentice i helped make a house lot of arched door frames out of 3mm ply and Selleys Aquadhere and i know for a fact that those frames still have doors swinging off them.
Similar Threads
-
What is the modern alternative to using Urea Formaldehyde for Bent Laminations ?
By RoyG in forum GLUEReplies: 6Last Post: 22nd January 2015, 10:26 AM -
Simple tapering jig for making laminations
By BenBrown in forum WOODWORK - GENERALReplies: 0Last Post: 9th May 2012, 11:11 PM -
Soft glue for bent laminations
By Artesano in forum GLUEReplies: 4Last Post: 12th March 2010, 10:02 PM -
bent laminations
By woodguy_1 in forum WOODTURNING - PEN TURNINGReplies: 1Last Post: 30th August 2005, 08:56 PM -
Laminations thickness
By JackG in forum WOODWORK - GENERALReplies: 10Last Post: 7th June 2005, 12:23 AM