Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Ozzie dowelling jig
-
10th February 2006, 03:31 PM #1SENIOR MEMBER
- Join Date
- Oct 2005
- Location
- North Balwyn Victoria
- Age
- 72
- Posts
- 520
Ozzie dowelling jig
Has anyone had the same experience with the jig being out of square? When used in the 'T' format it is noticably out of square, one block more than the other. When used to join boards they are reluctant to meet square, no such problem with a biscuit! I need to dowel splay legs into a table top & intended to use the Ozzie jig, can anyone offer another solution?
-
10th February 2006 03:31 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
10th February 2006, 03:55 PM #2
I've had an ozzie jig for a couple of years now made a few pieces of furniture with it and no probs always perfect alignment
I will post the link to Des Fenelon web page i'ts got an e-mail address , i'de be giveing him a call , if its out of alignment then he should replace the thing.
http://www.ozziejigs.com.au/
RgdsAshore
The trouble with life is there's no background music.
-
10th February 2006, 03:57 PM #3
The Ozzie Jig
Originally Posted by Emerald Pete
I was going to buy an Ozzie Jig at the Hobart WW Show but the guy selling them seemed so bored and disinterested when I asked him a question that I just walked away. His wife(?) was in the background repeatedly counting their take for the day and was equally uncommunicative.
They did seem to be a good jig but I guess I'll never know for sure.
CheersIf you never made a mistake, you never made anything!
-
10th February 2006, 04:24 PM #4
Not sure what you mean by the T format. Can you be more specific about what exactly is out of square with what?
I've had no problems with mine, except for the time I dropped it on the concrete floor and bent the end fence. Couple of blows with a hammer against the jig blocks put it back to square. I always get perfect alignment, and am still very happy with the OMJ.Those are my principles, and if you don't like them . . . well, I have others.
-
10th February 2006, 04:37 PM #5SENIOR MEMBER
- Join Date
- Oct 2005
- Location
- North Balwyn Victoria
- Age
- 72
- Posts
- 520
Hi Zenwood, by'T', I mean with the fence between the 2 blocks.Set yours up, place a straight edge across the 2 blocks & tell me it's flat, also place a square on the block against the fence & tell me it's 90 degrees.I can see daylight doing both tests. Am I just being precious?
-
11th February 2006, 10:58 AM #6
Pete,
Don't know if you're being precious, but here's mine for comparison. I'm perfectly happy with its performance.
Flatness test
Putting a straight edge across near the middle (pic 1) there is a slight ridge caused by the top of the central fence that makes the straight edge rock a bit (this would have no effect on the jig's performance). Putting the straight edge at the ends -- beyond the end of the middle section -- (pic 2, only took a photo of one end, but the other was the same), the surfaces are dead flat.
Squareness test
The left hand side (pic 3) is dead on. The right hand side (pic 4) shows a teeny bit of daylight at the doesn't worry me.
If your results are significantly worse that mine, and mean that you can't use your jig, I'd send your pics to Des Fenelon and ask his advice. I found him quite helpful at the last show after I dropped my jig, and he showed me how to bash it back into shape with a hammer. Helpful, but chose your timing carefully: during a lull in the demonstrations. I don't think he likes being interrupted while 'in the zone'.Those are my principles, and if you don't like them . . . well, I have others.
-
11th February 2006, 11:29 AM #7
Emerald I ran a square over mine as well and a fraction of light, the right angle was damm good though
Don't know accurate you need to be mine I would guess is within 1-2 thou
and for me thats more than enough
rgdsAshore
The trouble with life is there's no background music.
-
12th February 2006, 12:49 PM #8
Checked that gap on the right, and could just fit a 0.05mm feeler guage in there (2 thou.)
Those are my principles, and if you don't like them . . . well, I have others.
-
14th February 2006, 09:03 PM #9
I've had mine for years and never had a problem. That's mainly the reason I've never felt the need to buy a biscuit joiner.
Cheers,
Graeme
Similar Threads
-
Ozzie Multi Jig
By Doc Carver in forum WOODWORK - GENERALReplies: 23Last Post: 31st December 2012, 12:12 AM -
Dowelling Jig
By Mambo in forum HAND TOOLS - POWEREDReplies: 3Last Post: 4th June 2005, 09:13 PM -
Ozzie Multi Jig
By Iain in forum HAND TOOLS - POWEREDReplies: 2Last Post: 12th September 2003, 12:42 PM -
The 'Ozzie Multi Jig'
By Shane Watson in forum HAND TOOLS - POWEREDReplies: 9Last Post: 22nd June 2002, 01:07 PM