Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 5 of 5
  1. #1
    Join Date
    Dec 2005
    Location
    Western Australia
    Posts
    306

    Default Lawnmower won't start when hot!

    Not sure where to put this question, so thought I would start here....


    I bought a secondhand lawnmower the other day, it is a 11 year old Masport 4 stroke. It goes really well, starts first time, every time, two pumps of the primer and pull the cord, away she goes. Has a bucketload of power, cuts my buffalo lawn with ease.

    The problem I have is that it doesn't restart when hot. I have two lawns, and I can't mow one, turn the mower off, and move it to the next lawn, cause it won't restart! I have to idle the mower all the way down the side of the house to the front lawn.

    I tested it again today. I pulled it from the shed, primed it, then pulled the cord, bang, away she goes! Let it idle for 10 minutes, turn it off, and it wouldn't start.

    Any ideas as to what is wrong? Or and advice as to further tests I can do to establish what is wrong?

    Cheers

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Mar 2008
    Location
    Canberra, Australia
    Age
    62
    Posts
    316

    Default

    At a guess, it is either a compression, spark or fuel problem, more than likely a compression or spark problem.
    1. Compression - check the compression (with a compression guage) when it's cold and again when it's hot. If there is a dramatic difference, then it's stuffed and will need some work (new rings and maybe a rebore).
    2. Spark - when hot, remove the spark plug lead from the plug, connect it to a spare plug and earth the body of the plug to the engine, using a suitable clamp to hold it in place. Pull the starter cord and if you can see a spark jump across the gap betweeen the electrode and the plug's body, then all is OK. If not, then maybe the coil/points/sender are buggered.
    3. Fuel - unlikely, but if the above test OK, then maybe a fuel problem.

    P.S. This post is so old, he's probably gone a bought a new mower by now.
    The first step towards knowledge is to know that we are ignorant.

  4. #3
    Join Date
    Jun 2003
    Location
    ...
    Posts
    7,955

    Default

    Quote Originally Posted by Spelunx View Post
    Lawnmower won't start when it's hot!
    Neither will mine. Mainly because I refuse to mow the nature strip when it's hot. I'll wait on cooler weather.


    Peter.

  5. #4
    Join Date
    Dec 2004
    Location
    Northen Rivers NSW
    Age
    57
    Posts
    2,837

    Default

    Valve clearance may be too tight and is holding the exhaust valve open when hot.


  6. #5
    Join Date
    Oct 2006
    Location
    Tallahassee FL USA
    Age
    82
    Posts
    4,650

    Default

    Quote Originally Posted by dazzler View Post
    Valve clearance may be too tight and is holding the exhaust valve open when hot.
    Similar problem with Briggs & Stratton, too. The valve guides get hammered into the block so as to prevent complete closure. Solution is to grind about a hair's width off the valve stem length.

    Joe
    Of course truth is stranger than fiction.
    Fiction has to make sense. - Mark Twain

Similar Threads

  1. Hot water goes cold in the pipes: what to do
    By silentC in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 31
    Last Post: 19th July 2006, 10:16 AM
  2. Welding question ? ... Is this dangerous ?
    By JDarvall in forum WELDING
    Replies: 36
    Last Post: 9th March 2006, 12:29 PM
  3. Hot water system - Temperature regulations
    By notrot in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 19
    Last Post: 13th September 2005, 05:54 AM
  4. Gas hot water heaters
    By Bob Willson in forum NOTHING AT ALL TO DO WITH WOODWORK
    Replies: 28
    Last Post: 29th March 2005, 12:16 PM
  5. changing tap washers on hot water taps
    By jackiew in forum PLUMBING, ELECTRICAL, HEATING, COOLING, etc
    Replies: 85
    Last Post: 6th May 2004, 06:43 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •