Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 22
Thread: Backplate casting
-
22nd September 2008, 02:33 PM #1
Backplate casting
As you may remember, the Zyto lathe that I bought recently did not come with a 4-jaw chuck or a backplate for such a thing. So I will buy an old 3 1/2 - 4" 4-jaw chuck (Mick Moyles says they have several for me to look at) and try to make or have made a backplate to fit it.
It seems from the Lathes.co.uk site that for a lathe of the vintage of the Zyto (1940s-50s) the backplate should be made from free-drawn cast iron. Does anyone know where one can obtain rough cast backplates of a suitable size? Or do you just use a lump of cast iron and machine it down to the required sizes?
Do you reckon that I should be able to do this machining job by holding the cast iron in the 3 jaw by drilling and tapping a 1/2" hole in the back of the cast iron and loctiting a stud in for the jaws to grip while the rear face is turned down. Or should I get an engineering shop to make one for me? If the latter - any suggestions for a Sydney-based shop that would do such a weird one-off job and not charge an arm and a leg?
Sorry for some of the stream-of-consciousness, here, I am just trying to work out what the best way to proceed is likely to be.Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
22nd September 2008 02:33 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
22nd September 2008, 03:44 PM #2GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
Jeremy
Similar thread here.
I'm still waiting to hear from a local supplier whether they can get the backplate I need.
If not, then I'll also be looking for a place to make one for me.
As you're looking to install a smaller chuck, these cast plates may be suitable as a start point.Last edited by snowyskiesau; 22nd September 2008 at 03:46 PM. Reason: Added link.
Geoff
The view from home
-
22nd September 2008, 03:50 PM #3
There was a post somewhere on here of a plate made from a cast iron weight lifting weight. (I think it was here)
-
22nd September 2008, 03:53 PM #4
I've been following your thread, Geoff.
I had forgotten Hobby Mechanics - I reckon one of their castings would be fine for me - I will just have to work out how to bore the centre hole and thread it accurately. Should be doable. If not someone should be able to do it or me, once I have bought my 4-jaw.Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
22nd September 2008, 04:14 PM #5GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
You can get pieces of cast iron 4E I sourced some prices for 150mmODX50mmTH round figures $30.00 and 200mmODX50mmTH $50.00 this material would be suitable for your backing plates,these sizes are just an example.
-
22nd September 2008, 04:19 PM #6GOLD MEMBER
- Join Date
- Jul 2006
- Location
- Port Huon
- Posts
- 2,685
You can get pieces of cast iron 4E I sourced some prices for 150mmODX50mmTH round figures $30.00 and 200mmODX50mmTH $50.00 this material would be suitable for your backing plates,these sizes are just an example.Geoff
The view from home
-
22nd September 2008, 04:20 PM #7
Jeremy,
It should be possible to do it yourself if your lathe has appropriate screw cutting facilities.
It is simply a case of mounting the raw backplate in the 3 jaw and drilling a basic undersize center hole, then maching that to size. If at all possible, cut a thread to match the spindle rather than tapping it. Test regularly while cutting the thread by removing the complete 3 jaw and backplate setup, reversing and presenting to the spindle to test.
Once you are satisfied that the thread is good and a well fitted, remount as a set and turn the boss and what will be the back face of the plate until you are getting an even cut over the surface and turn any registers that are required for the spindle.
Only then should you release the unit from the 3 jaw, mount it directly on the spindle and machine the face and edge to match the chuck.
This sequence should result in a chuck that runs true with a well balanced backplate. It should be possible to remove the chuck and backplate as a unit and return them to the spindle without affecting setup accuracy etc.
-
22nd September 2008, 04:26 PM #8GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
-
22nd September 2008, 04:28 PM #9GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
-
22nd September 2008, 04:49 PM #10
Quite right, pipeclay. I have sourced some 2P cast iron rod which I could hacksaw into a disc, but I could not hold that disc in the 3-jaw. However, I could tap in the rod and turn the back down so that it has a boss on it that could be held in the 3-jaw and then proceed as malb indicated. The only problem I have is that I am also missing some of the thread cutting gears....I will have to see if I can do a 9tpi internal screw....
Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
22nd September 2008, 04:50 PM #11
-
22nd September 2008, 05:04 PM #12GOLD MEMBER
- Join Date
- Jun 2007
- Location
- sydney
- Age
- 64
- Posts
- 3,566
No secret Edcon.
-
22nd September 2008, 05:05 PM #13Pink 10EE owner
- Join Date
- Aug 2008
- Location
- near Rockhampton
- Posts
- 4,304
I get my cast iron from the local bolt and steel supplier...
-
22nd September 2008, 05:10 PM #14
-
22nd September 2008, 09:46 PM #15
Similar Threads
-
Work around for the Zyto backplate?
By jmk89 in forum METALWORK FORUMReplies: 4Last Post: 22nd August 2008, 11:06 PM -
Pigments for casting
By schaf in forum CASTING & STABILISATIONReplies: 2Last Post: 26th July 2008, 11:57 PM -
Casting PR blanks
By Big Shed in forum CASTING & STABILISATIONReplies: 19Last Post: 19th May 2008, 09:36 PM -
casting aluminium
By mic-d in forum THE FOUNDRYReplies: 8Last Post: 23rd May 2006, 01:18 AM -
Aluminum Casting?
By MajorPanic in forum WOODWORK - GENERALReplies: 11Last Post: 10th January 2004, 03:07 PM