Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Help Needed Rotel cd player
-
27th December 2008, 06:26 PM #1
Help Needed Rotel cd player
Hi Guys
My rotel cd has stopped working. When I load a disk it spins it for about a second then stops and sends an error code to the display panel. It did this for a while so I unplugged it and used another, but decided to give it another go and it worked perfectly for another week. Now its given up again.
I pulled the cover off and cleaned the laser to no avail. Nothing seems obviously destroyed to my untrained eye, however the laser mechanism is sort of floating in the breeze, it isn't at either end of its travel just floating in the middle. I think when the machine powers up it moves to one end, might be electromagnetic. But what would I know?
Any ideas?
Any idea where to have it looked at?Cheers
Jim
"I see dumb peope!"
-
27th December 2008 06:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
28th December 2008, 12:19 AM #2
Anything Rotel would be worth getting looked at by a pro, maybe ask a few specialist hifi shops to see who they use.
....................................................................
-
28th December 2008, 11:46 AM #3
This may be unrelated but recently 1 of my amps would switch off as soon as it was turned on. We've had very humid weather later and i suspected this may be causing the problem so kept persisting with the on/off business. It started staying on about a 1/4 second longer each time till it eventually worked. If you've had similar weather lately, try just leaving it switch on for a while and the heat inside will evaporate any moisture build up. That reminds me, I had a similar problem with a Marantz DVD player years ago that didn't get much use and the above remedy worked. Good luck, hope it's a cheap fix.
-
28th December 2008, 08:45 PM #4
Rotel were imported by International Dynamics in Melbourne. This was the wholesale arm of Encel Electronics who have been advertising recently, so must still be out there. That should give you a couple of places to google, though there aren't particularly close to home.
-
5th January 2009, 12:21 AM #5
Realy there is nothing special about Rotel, just typical mid range product.
Most likley is the laser is on the way out. If it is one of the older machines,a good audio tech who knows his CD players might tweek the alignment & get it to run a little longer.
Most likley it will be one of the off the shelf laser modules, most CD players use one of several brands of laser, you can problay get a replacement laser.
If it is a more modern design there is no alignment adjustments. you just replace the laser.....serioulsy any body with a bit of care and fingers smaller than bananas can do it.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
10th January 2009, 05:54 PM #6Senior Member
- Join Date
- Aug 2006
- Location
- Oyster Bay NSW
- Posts
- 120
-
18th June 2009, 06:31 PM #7New Member
- Join Date
- Nov 2008
- Location
- Adelaide, Australia
- Posts
- 2
Could be the laser, but could also be the belt that drives the CD drawer, I had a similar problem with my NAD - turned out the belt was stretched and although the drawer closes OK, it would not send the right signal to the control electronics and the machine would think there is no CD in the tray.
Changing the belt (50 cents worth) fixed it for me.
Good luck.
Stan
Similar Threads
-
Installing CD player in Sprinter
By Rossluck in forum MOTOR VEHICLESReplies: 4Last Post: 11th January 2008, 03:31 PM -
CD Player
By alisonol in forum HI FI EQUIPMENTReplies: 8Last Post: 29th May 2007, 07:39 PM -
DVD player question
By Rossluck in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 12Last Post: 18th January 2007, 01:32 PM -
a poker player
By Cliff Rogers in forum WOODIES JOKESReplies: 1Last Post: 21st February 2005, 10:38 PM -
mp3 player and FM transmitter
By simon c in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 1Last Post: 31st January 2005, 09:58 PM