Thanks: 0
Likes: 0
Needs Pictures: 0
Results 1 to 8 of 8
Thread: Hand saw screws & nuts.
-
15th January 2009, 01:52 PM #1
Hand saw screws & nuts.
I have an old Disston hand saw which belonged to my Dad. The handle is knocked about so I will make a new one.. Any idea where I can get screws & nuts for it? Maybe somebody can identify it for me also. It is a skew back, 23 " from tip to the 1st. screw. It is a rip saw and is only 5 pts. per inch. It is only 20mm wide at the tip. Is it a panel saw?
Just Do It !
-
15th January 2009 01:52 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
15th January 2009, 02:20 PM #2
As for the saw nuts, I think the best thing you can do is to try to use the ones that you have already - get a cheap blade screwdriver and use an angle grinder to cur a slot in the blade so you can use it to undo the nuts.
Alternatively, you may end up having to make your own - how to do that is detailed on Norse WoodsmithCheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
15th January 2009, 02:38 PM #3
Must be psychic, I just started a thread on group purchase of split nuts!
Regards
Ray
-
16th January 2009, 10:00 AM #4
the saw nuts and bolts are called chicago nuts and bolts and the best way to get replacements is to go to a saw sharpening doctor or buy a crapped out saw from a garage sale and use the bolts from them.
in newcastle i went to newcastle industrial sharpening were an old gentleman use to work and he had a collection i paid about $2 per nut and bolt.
try the disstonian institute.com for a history on disstons and restoration technics
best wishes and good luck
greg
-
16th January 2009, 10:10 AM #5
Thank you fellas for your replies. I think I may have sourced what I require. The Saw Doctor is also a good idea. I will get a full set if possible as some of them look OK but are worn on the shanks because the blade has been loose in the handle & chewed them up. I see a couple of good sites re. saw handle making on the web also.
Regards.
Al.Just Do It !
-
18th January 2009, 09:08 AM #6Member
- Join Date
- Jun 2008
- Location
- Melbourne
- Posts
- 76
Patonga,
I almost certainly have one the same, from my dad or grandad. I have restored several old Disstons and have bought a bunch of assorted nuts on US ebay from time to time. Cost me about $20 for a hundred or so, all mixed but I was able to make up a few sets. Many medallions too. Of course you never have the exact one you want....
I agree with the old saw at the market plan - you often see a throw-away relic but the nuts are all there. Usually less than $5.
BR,
Fraser
-
18th January 2009, 07:38 PM #7
"I agree with the old saw at the market plan - you often see a throw-away relic but the nuts are all there. Usually less than $5."
BR,
Fraser[/quote]
Fraser,
"The old saw at the market" is a good idea I'll remember it. May even find something else to restore. Had a look at the handle today. I was wondering how I was going to cut the slot as I had a look at some refurbishing tips on the web & one bloke had to use a slitting saw of some kind. I am lucky as there are no radiused cuts required so I can just use a back saw.
regards & thanks to all who came up with suggestions.
Alan.Just Do It !
-
19th January 2009, 01:51 PM #8SENIOR MEMBER
- Join Date
- Apr 2005
- Location
- Nambour Qld
- Age
- 88
- Posts
- 688
The Carb-I-Tool catalogue lists saw screws. They are on page 44, Part No. SSCREW.
I haven't had reason to buy any, but a Carb-I-Tool router bit reseller should be able to order them in.Brian
Similar Threads
-
Wall storage system for screws, nuts, nails etc
By Lipsmacker01 in forum WOODWORK - GENERALReplies: 2Last Post: 15th November 2008, 01:10 AM -
Gal Screws v Zinc Screws. When to use what?
By Dr - 307 in forum FLOORING, DECKING, STUMPS, etc.Replies: 9Last Post: 13th December 2007, 07:48 AM -
Lag screws and tee nuts
By macca2 in forum WOODWORK - GENERALReplies: 3Last Post: 29th December 2005, 11:22 PM