Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 24
Thread: Nitro laquer
-
8th January 2007, 11:35 PM #1
Nitro laquer
Hey guys,
I got a quote for mirotone lacquer today, $39 for 4 litres of the lacquer and $50 for 4 litres of thinner.
Seems like the thinner is expensive to me. Did anyone ever used all-purpose thinners before like you find at Bunnings? Anyone knows if that stuff is compatible with nitro?
-
8th January 2007 11:35 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
9th January 2007, 12:49 AM #2
Phil,
you can use the cheap lacquer thinners that Suprecheap Auto and other discount type places sell (about $20 - $25 per 4l) but for the final top coat you should use a good one otherwise I've found that you just don't get the right gloss level (bit dull). I've bought mine from automotive paint suppliers in the past in 20l drums, can't remember how much but it was considerably cheaper than even the el cheapo stuff. As long as it's labelled as lacquer thinners it should be compatible.
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
9th January 2007, 02:17 AM #3Senior Member
- Join Date
- Jan 2006
- Location
- aust
- Posts
- 271
You'll get away with most high level thinners, but they are all expensive. From memory, the Mirotone stuff has a slightly different smell to it, compared with other thinners, but maybe im thinking of something else. If you are using thinners to clean your guns, try gun wash, its cheaper, saving you the good stuff for the lacquer.
If its $$ per litre you are worried about, consider a 20 litre drum, should be about $90-130 depending on the source.
Im sure i have a 40 litre drum in stock now that cost $165. Thats $4 a litre.
-
9th January 2007, 04:21 PM #4
Hey Phil
Theyr'e good to you up in Brisbane
I got quoted around $65 @ 4lt Mirotone Nitro Lacquer here in Adelaide and when I told them I was going to use it for guitar building they told me none of their products were suitable for this
Anyhow, I contacted Protec here in Adelaide and I managed to pick up a 4lt of sanding sealer and NC topcoat for the same price. Their top thinners to suit $28 @ 4lt
Ive sprayed a few cars in my time and Ide agree with journeyman Micks comments about using a quality thinner for your final coats
dayvo
-
9th January 2007, 05:46 PM #5
-
9th January 2007, 11:49 PM #6
Thanks for the reply guys. Perry, I already use gunwash not to use up the good stuff but it was a good tip
I think I'll go for the 20 litre stuff anyway. I got quoted 40$ for 4 litres of lacquer and 120$ for 20. Hell of a reduction. At least 20 litres should last me a couple of years. I'll do the same with the thinner.
-
10th January 2007, 10:21 AM #7Member
- Join Date
- Sep 2006
- Location
- Canberra
- Posts
- 97
Nitro safety
Hey, while we are talking about spraying nitro I have a few safety questions.
I read that you have to be careful with venting fans in you spray booth/room as the wrong one can ignite the vapour. Does anyone have any experience with setting up a small booth? Also, I am about to buy some gear and would like to get recommendations about the size of air comp and good gun brands etc. Any help most appreciated.
Cheers
Dom
-
10th January 2007, 12:09 PM #8Saw dust maker!
- Join Date
- Sep 2006
- Location
- Wandong
- Age
- 60
- Posts
- 453
Gday Dom
Generaly speaking from an electrical view, motors, lights and any electrical devices must have a 'Class 1, Zone 1' rating (ie: explosion proof. It's not designed to keep the gases out, but to keep the explosion in). It's easy to tell if it has this rating by the chunky look of the equipment and the overuse of bolts to hold it all together. If there's a nameplate on it, somewhere there will be 'Ex' stamped on it.
There are ways around it though... Such as mounting lights external to the booth and sealing them up and purging them with air from a safe zone. Motors for extraction fans can be mounted external as well (in a safe area) with a belt drive to the fan impellor.
Class 1, Zone 1 equipment would be out of the budget for home spray booths. For example, a normal oyster light fitting would be 50 bucks and an Ex rated fitting about 500 (A guess, but horrendously priced stuff!).
Using a radio, drill or even a normal extension lead in an explosion zone is big time taboo!
Hope this helps
-
11th January 2007, 12:04 AM #9Novice
- Join Date
- Jan 2007
- Location
- Adelaide
- Posts
- 15
Mirotone tips.
Hey Guys. Just browsing, and saw a post for Nitro Laquer. Please allow me to share my, and my guitar builder mates experience with Mirotone. First, I know it is expensive, but as an acid catylised laquer, It really needs its its own specific thinners. You can use other thinners, but it will craze. If thats what you want, use it, It works for "relic-ing" guitars etc. The other problem is, Super cheap auto thinners makes it go jelly like in the gun. If you use the correct thinners, then gun cleaner to clean, look out. It will clag up and then you gotta strip the gun. I flush and blow back the gun with M/tone thinners, then do the same with s/cheap thinners, then use M/tone to keep the gun wet when it's idle. Yes...I know it's expensive, but believe me, after spraying dozens of guitars, just use the right thinners. Scraping a guitar back because it's got a crap finnish is boring. I also use a gravity feed gun, it's more economical, and easier to clean Now..3602 laquer is good, but toxic as all get out. 3606 is just as good, and less toxic. STILL TOXIC!! I hope you have a positive pressure mask, booth or carbon mask or a good combination. Also, Protec Nitro doesn't go as hard as an acid cat, it doesn't look as good either in my opinion. Also, if you go too hard with the buff it will drag and is less forgiving.Sorry about that. Also...Hi build sealers are convenient, but they are not totally transparent, and look cloudy, I am a bit fussy maybe but there it is. They also chip "white" and are horrible to repair and touch up, if you have ever tried to fix a chip in a post 1990 Maton, you know what I mean. The best grain filler for Mirotone is a slow cure epoxy resin like Megapoxy by resimax. BoatCote is a rip-off, but excellent in use. Use top coat as a build coat. 6 coats 20% reduced, then sand back with 600 wet, then hit it with a 30% reduced top coat x 2 in one go, and you will see a good result. Dust proof fans with no ingress cavities will work as flame proof fans. But if you wanna be sure, spend the money on a certified fan!! Cheers, good luck, I hope this helps someone. I have been wrestling this stuff for years with guidence, and still get frustrated. Steve.
-
11th January 2007, 12:32 AM #10
Interesting post Steve So I guess from your post you usse Mirotone's Acid-Catalyst lacquer? That's a different product than Nitro though.
So I went to Mirotone's office today to get my nitro-cellulose which the lady on the phone reserved for me. (product name:Mirolac) I end up getting a tin of Mirocat (pre-catalized lacquer). I obviously asked the lady what's the deal since I specifically asked for Mirolac nitro-cellulose lacquer. She had no idea what I was talking about. The other guy in the office strarts asking me why I want that and they haven't made that stuff for years and blah-blah-blah. Why the hell is that product on their website if they don't make it!!!!!!
So I ended up leaving with a tin of mirocat anyway. The spec sheets made it look pretty similar to nitro. I guess I'll try that stuff. I have to finish a hardwood desk I just build so it'll give me a chance to try it before I use it on a bass.
Anybody tried Mirocat before? Any opinions?
And their acid-catalyst one (mirobild)? Anyone use it or like it? (Steve?)
-
11th January 2007, 02:48 AM #11
Phil,
I've used nothing but Mirocat for about 5 years now. I do recall quite a few years back when I asked for NC lacquer (Mirolac) I was told by my supplier that they no longer carried it as most people prefered the pre cat (Mirocat). I"ve also used the acid cure (can't remember which one) as it was specced for a job. Pros and cons of each:
Mirocat:
Pros:
cheap (relatively speaking)
sands very easily with very minimal clogging of abrasives
easily refinished
applies very easily
not too toxic
smell is not too strong and disperses quickly
Cons:
very sensitive to white "bloom" or "blush" if spraying in high humidity/low temp (but easily remedied by warming the piece up in the sun the next day and spraying it with thinners)
not as hard wearing as acid cure
Acid cat:
Pros:
much more forgiving of high humidity/low temp conditions, BUT if you do get blush you'll need to sand back and spray again.
much harder wearing than pre-cat
Cons:
more expensive than pre-cat
extremely unpleasant, toxic fumes which take quite a while to disperse
doesn't sand as easily and clogs paper more than pre-cat
refinishing requires sanding right back
On the whole, nowadays I'm more likely to apply a coating which I know will be easy to eventually refinish rather than one which is a lot harder wearing but which requires considerable effort to refinish. (In other words I'd use pre-cat over acid cure or poly-u 2 pack)
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
11th January 2007, 08:00 AM #12
Thanks Mick,
How would you compare the solidity of the Mirocat film compared with NC?
-
11th January 2007, 10:32 AM #13Member
- Join Date
- Sep 2006
- Location
- Canberra
- Posts
- 97
Thanks for the safety advice Malibu. And to all the other contributors for the handy tips. I read somewhere in here that hard shellac does a good job without the problems with NC. Might try that until I get myself organised with proper spray gear.
Cheers
Dom
-
11th January 2007, 12:10 PM #14
-
11th January 2007, 12:17 PM #15
Similar Threads
-
Wanted: thin, hardwearing, glossy finish for solidbody guitars
By JupiterCreek in forum FINISHINGReplies: 67Last Post: 20th December 2006, 10:21 PM -
Sources of Nitro in Sydney
By philly in forum MUSICAL INSTRUMENTSReplies: 3Last Post: 3rd November 2006, 02:47 PM -
nitro celulose
By dennis perkin in forum FINISHINGReplies: 1Last Post: 17th July 2006, 08:19 PM -
Gloss laquer on cyp pine floor WITHOUT colour change
By Danster in forum FINISHINGReplies: 12Last Post: 1st August 2004, 12:18 PM -
Laquer over shellac????
By gregster in forum FINISHINGReplies: 5Last Post: 26th March 2004, 06:27 AM