Search:

Tag: chipmaster

Search: Search took 0.00 seconds.

  1. Colchester Chipmaster Tracer Attachment

    Started by Piers037, 29th August 2014 10:49 PM
    attachment, chipmaster, colchester, tracer, tracer attachment 4 Attachment(s)
    • Replies: 7
    • Views: 1,915
    Last Post: 2nd September 2014 12:09 PM
    by Steamwhisperer  Go to last post

    Forum:
    METALWORK FORUM

  2. my new toy. Colchester Chipmaster

    Started by thorens, 24th July 2014 11:50 AM
    4 Pages •
    1 2 3 4
    adjusting, chipmaster, cleaning, colchester, finally, home, peter, time, toy 5 Attachment(s)
    • Replies: 45
    • Views: 5,385
    Last Post: 8th August 2014 05:33 AM
    by samthedog  Go to last post

    Forum:
    METALWORK FORUM

  3. Camlock query

    Started by morrisman, 31st May 2014 12:04 AM
    360, apply, backplate, camlock, chipmaster, degrees, eccentric, feel, force, hub, line, locking, loose, marked, marking, mike, noticed, past, pins, pivots, position, pulling, query, screwed, supposed, tightening
    • Replies: 8
    • Views: 1,739
    Last Post: 31st May 2014 10:47 PM
    by morrisman  Go to last post

    Forum:
    METALWORK FORUM

  4. One for the steam tragics.....

    Started by PDW, 22nd March 2014 08:13 PM
    2 Pages •
    1 2
    arboga, arm, bantam, bargain, bring, btw, cheap, chipmaster, companion, competition, cost, day, dover, drill, drive, earth, expect, half, happy, hours, increasing, lathe, maximat, mind, pdw, radial, real, sell, steam, tragics
    • Replies: 15
    • Views: 3,000
    Last Post: 29th March 2014 07:19 AM
    by Steamwhisperer  Go to last post

    Forum:
    METALWORK FORUM

  5. Chipmaster Thread Cutting

    Started by Piers037, 6th August 2013 11:03 PM
    2 Pages •
    1 2
    appears, carnage, centre, cheers, chipmaster, compound, crank, cross, cut, cutting, dial, disengage, engage, galling, half, hand, height, lash, missing, nut, piers, ripping, screw, set, slide, thou, thread, touch, treads, wind 7 Attachment(s)
    • Replies: 24
    • Views: 3,368
    Last Post: 10th August 2013 01:08 AM
    by j.ashburn  Go to last post

    Forum:
    METALWORK FORUM

  6. Colchester Chipmaster thread engagement lever problem

    Started by achjimmy, 9th June 2013 10:11 AM
    advises, atm, ball, chipmaster, chipped, chippy, clasp, cleaned, colchester, cutting, drawings, engagement, finish, hole, lead, lever, manual, moves, nut, problem, remove, rollers, saddle, screw, sprayed, spring, step, thread, tool, wd40 2 Attachment(s)
    • Replies: 10
    • Views: 1,916
    Last Post: 10th June 2013 03:10 PM
    by achjimmy  Go to last post

    Forum:
    METALWORK FORUM

  7. RDG test bar for lathes

    Started by morrisman, 15th April 2013 03:29 PM
    300, 3mt, bantham, bar, bars, checking, chipmaster, ebay, lathe, lathes, length, m300, mike, morse, parallel, procedure/method, rdg, rdgtools, short, taper, test, usual 2 Attachment(s)
    • Replies: 7
    • Views: 1,914
    Last Post: 16th April 2013 07:58 AM
    by Michael G  Go to last post

    Forum:
    METALWORK FORUM

  8. Toowoomba:colchester chipmaster lathe $1495

    Started by damian, 14th February 2010 02:37 PM
    $1495, $1900, 550, bed, buy, chipmaster, colchester, disagree, gentleman, haigslea, handy, home, iver, lathe, lot, machine, nice, pass, people, personally, plate, rigid, selling, size, speed, swap, toowoombacolchester, trailer, understood, variable
    • Replies: 5
    • Views: 3,126
    Last Post: 16th February 2010 11:40 AM
    by damian  Go to last post

    Forum:
    METALWORK FORUM

Results 1 to 8 of 8