Search:

Tag: straightedge

Search: Search took 0.00 seconds.

  1. Thicknesser cutting unevenly

    Started by Tiger, 25th July 2012 12:21 PM
    2 Pages •
    1 2
    0.3, 0.6, caliper, check, checked, concerns, cutting, digital, exact, expecting, flat, gmc, jointed, length, line, low-end, machine, mitres, notice, pretty, properly, running, straightedge, thicknesser, thicknesses, thinner, timber, unevenly
    • Replies: 17
    • Views: 3,194
    Last Post: 1st August 2012 11:21 PM
    by Tiger  Go to last post

    Forum:
    GENERAL & SMALL MACHINERY

  2. know where to buy a good straightedge ?

    Started by JDarvall, 17th June 2011 04:17 AM
    2 Pages •
    1 2
    1000, 1mm, 40mm, bar, bending, beveled, bloke, buy, carba-tec, checking, edge, glueups, good, ideally, jake, means, mind, sharp, solid, spring, straight, straightedge, straightedges, thick, thinking, time, veritas, veritas®, whatsoever, worried
    • Replies: 24
    • Views: 9,037
    Last Post: 21st June 2011 11:50 AM
    by mat  Go to last post

    Forum:
    WOODWORK - GENERAL

  3. Blade weld mis-alignment

    Started by JohnMurray71, 29th March 2010 09:42 PM
    0.5mm, 3/4, 3tpi, acceptable, bandsaw, blade, carbatec, coming, concave, confirms, contact, couple, cuts, estimate, found, grandmas, house, idea, john, laying, mis-alignment, misalignment, purchased, return, running, straightedge, thrust, tolerances, weld, welds
    • Replies: 6
    • Views: 1,430
    Last Post: 31st March 2010 09:07 AM
    by Enfield Guy  Go to last post

    Forum:
    BANDSAWS

  4. Straightedge - Veritas, Stewmac, Starrett or...?

    Started by highfieldtonewerks, 15th February 2010 06:34 PM
    2.4mm, 4mm, advance, brand, cents, chuck, dollars, gday, ideal, keeping, local, market, prefer, preference, reasons, shop, source, starrett, stewmac, straightedge, veritas, wondering
    • Replies: 7
    • Views: 2,288
    Last Post: 17th February 2010 08:40 PM
    by Groggy  Go to last post

    Forum:
    MUSICAL INSTRUMENTS

  5. Makita Plunge Cut Circular Track Saw V Regular Circular Saw

    Started by groeneaj, 11th April 2009 07:51 PM
    2 Pages •
    1 2
    accurate, andy, appeals, bences, boxes, circular, cut, cuts, cutting, easy, guys, input, ls1214l, makita, obviouslly, offer, payment, plunge, practice, racks, rails, ranges, regular, set, sort, storage, straight, straightedge, track, wine
    • Replies: 20
    • Views: 20,712
    Last Post: 15th April 2009 01:07 AM
    by montiee  Go to last post

    Forum:
    HAND TOOLS - POWERED

  6. Testing Sharpness of, and Setting, Planer Blades

    Started by DanSplinters, 4th January 2009 11:42 AM
    adjustable, advice, bed, beds, bench, blades, combination, cutterhead, cylinder/barrel, dan, determine, diameter, extend, extending, gilbro, height, infeed, jointer, means, outfeed, planer, setting, sharp, sharpness, simple, straightedge, testing, tests, unit, workmate
    • Replies: 7
    • Views: 3,407
    Last Post: 4th January 2009 08:44 PM
    by mic-d  Go to last post

    Forum:
    SHARPENING

  7. Settng jointer blades

    Started by Fencepost2, 1st December 2008 10:32 PM
    2 Pages •
    1 2
    blade, blades, centre, cutter, dead, gap, head, height, helped, hold, inch, internal, jointer, level, magnet, magnets, metal, plates, pull, rotate, settng, snap, springs, steel, straightedge, table, tables, tighten, top, treat
    • Replies: 16
    • Views: 2,874
    Last Post: 8th December 2008 06:31 PM
    by Fencepost2  Go to last post

    Forum:
    WOODWORK - GENERAL

  8. How flat should my table be?

    Started by matto1, 17th September 2008 09:54 PM
    300mm, assembly, bad, blade, cheers, closest, day, edge, edges, expect, fine, flat, half, hoping, initial, matto, movement, normal, onlyinfront, range, replaced, screws, sit, sort, straightedge, stuff, switched, table, tolerances, worst
    • Replies: 3
    • Views: 1,534
    Last Post: 26th September 2008 11:46 AM
    by Edwards  Go to last post

    Forum:
    BANDSAWS

  9. Tension measurement?

    Started by Fencepost2, 13th April 2008 07:29 PM
    0.07mm, 0.7mm, 1.4/2, 1.4mm, 125mm, add, assuming, blade, distance, elasticities, feeler, fork, gauges, ideas, inches, increasing, length, measurement, move, occur, rise, spindle, spindles, straightedge, stretch, tension, times, top, tuning, wheels
    • Replies: 10
    • Views: 2,910
    Last Post: 15th April 2008 02:16 PM
    by Fencepost2  Go to last post

    Forum:
    BANDSAWS

  10. What is the most versatile routing jig?

    Started by Tiger, 3rd January 2007 12:26 AM
    abyss, agree, coming, disappeared, experts, found, hankering, jig, jigs, lot, lots, past, power, regularly, router, routing, simple, space, square, statement, store, straightedge, tool, ultra, usage, versatile, wooden, woodworking
    • Replies: 4
    • Views: 1,726
    Last Post: 4th January 2007 07:56 AM
    by Tiger  Go to last post

    Forum:
    ROUTING FORUM

  11. Straightedge

    Started by floyd7, 5th August 2006 12:28 AM
    buy, decent, straightedge
    • Replies: 10
    • Views: 1,931
    Last Post: 8th August 2006 10:04 PM
    by floyd7  Go to last post

    Forum:
    HAND TOOLS - POWERED

Results 1 to 11 of 12