Search:

Tag: rakers

Search: Search took 0.00 seconds.

  1. Rakers

    Started by MAPLEMAN, 3rd December 2013 09:30 AM
    4 Pages •
    1 2 3 4
    27rx, appreciated, average, bloke, bought, chainsaw, chainsoregon, corrugated, cut, cutting, day, leaving, mm2tsup, muchly, rakers, sharpened, shop, skip, tooth, tops, touched 13 Attachment(s)
    • Replies: 50
    • Views: 6,105
    Last Post: 23rd December 2013 10:00 AM
    by Sigidi  Go to last post

    Forum:
    SMALL TIMBER MILLING

  2. lucas slabber rising in the cut

    Started by footrot, 21st September 2013 02:09 PM
    2 Pages •
    1 2
    advice, bar, bit, blade, bowing, callipers, carlton, chain, cut, deg, degree, file, filed, filing, hole, length, log, loss, lucas, measured, middle, plate, rails, rakers, rising, slabber, square, substantially, teeth, trouble 1 Attachment(s)
    • Replies: 29
    • Views: 4,849
    Last Post: 13th November 2013 09:59 PM
    by Sigidi  Go to last post

    Forum:
    SMALL TIMBER MILLING

  3. 3/8th skip tooth reply

    Started by Krunchie, 6th September 2011 05:56 PM
    3 or 8th, bar, chain, cleaned, compare, conclusion, cut, cutter, cutters, drag, green, issue, issues, joining, leave, link, nose, pain, pic, preliminary, rakers, reply, result, rough, roughly, skip, speed, time, tooth, trial
    • Replies: 9
    • Views: 2,193
    Last Post: 8th September 2011 11:23 PM
    by Krunchie  Go to last post

    Forum:
    SMALL TIMBER MILLING

  4. Sigidi's new toys...

    Started by Sigidi, 28th July 2011 10:22 AM
    2 Pages •
    1 2
    attachment, breakages, build, chain, couple, file, file-o-plate, handles, hold, keeping, lucas, material, noticed, oil, pins, raker, rakers, reduce, round, sawdust/oil, sigidi, slab, slabber, slabbing, sprocket, tip, toolkit, toys, underside, warned
    • Replies: 24
    • Views: 4,237
    Last Post: 2nd August 2011 12:30 PM
    by milwise  Go to last post

    Forum:
    SMALL TIMBER MILLING

  5. chain cutters rakers etc

    Started by pjt, 3rd November 2009 11:35 PM
    4 Pages •
    1 2 3 4
    1/10th, 121119, 121125121126, angle, bob, bobl, btm, chain, check, chips, comments, cutter, cutters, disagree, enuff, gullet, load, lots, maintaining, makes, measured, measuring, paralell, quick, raker, rakers, rule, set, thread, touch
    • Replies: 47
    • Views: 10,165
    Last Post: 4th February 2010 06:35 PM
    by Travis Edwards  Go to last post

    Forum:
    SMALL TIMBER MILLING

  6. 1/10th rule

    Started by pjt, 18th October 2009 11:42 AM
    2 Pages •
    1 2
    .78mm, 1 or 10th, 1/10th, 404, 7.8mm, applying, assuming, bit, bobl, cadagi, chain, chain119357, chips, cutter, cutters, depth, dust, gadget, gadget119361, gullet, ideal, measured, peter, raker, rakers, rule, sound, this119360, top, width 4 Attachment(s)
    • Replies: 21
    • Views: 4,982
    Last Post: 19th January 2010 10:17 AM
    by pjt  Go to last post

    Forum:
    SMALL TIMBER MILLING

  7. ripping chain jumping around

    Started by footrot, 12th December 2009 10:04 PM
    10mm, 30-40mm, 30mm, blade, carlton, chain, cheers, cut, degrees, factory, fine, grinding, jumping, jumps, kerf, leaving, lot, lucas, rakers, recently, ripping, skip, slabber, start, stops, suggest, swap, teeth, tooth, wrong
    • Replies: 10
    • Views: 2,563
    Last Post: 13th December 2009 08:30 PM
    by weisyboy  Go to last post

    Forum:
    SMALL TIMBER MILLING

  8. Whats the diagnosis Dr BOBL? (chain surgon )

    Started by Krunchie, 24th November 2009 07:18 PM
    3/16, 7/32, 85-90%, bar, basted, bite, bob, bobl, chain, cheers, cuts, deal, diagnosis, engine, extra, felling, file, fire, grubby, hows, job, load, p.s, push, rakers, rob, stays, stop, stumps, surgon
    • Replies: 13
    • Views: 2,187
    Last Post: 26th November 2009 11:18 PM
    by BobL  Go to last post

    Forum:
    SMALL TIMBER MILLING

  9. No Excuses Milling

    Started by BobL, 21st November 2009 11:19 PM
    camera, chips, couple, damn, day, dropped, dust, excuses, file, finally, fingers, flu, grain, left, loader/forklift, lot, milled, milling, move, nice, phone, rakers, sawdust, shots, sorts, sprayed, started, strokes, wind, worried
    • Replies: 5
    • Views: 2,284
    Last Post: 25th November 2009 12:05 PM
    by Sigidi  Go to last post

    Forum:
    SMALL TIMBER MILLING

Results 1 to 9 of 10