Search:

Tag: bsf

Search: Search took 0.00 seconds.

  1. 9/32 BSF tap

    Started by rogerbaker, 3rd March 2015 10:46 AM
    9 or 32, bsf, tap
    • Replies: 11
    • Views: 1,235
    Last Post: 25th March 2015 06:53 PM
    by mugget  Go to last post

    Forum:
    METALWORK FORUM

  2. 1" BSP as a nut & bolt thread.

    Started by bob ward, 21st July 2014 11:31 PM
    1.125/1.25, 9tpi, australia, bolt, box, bsf, bsp, bsp-11, bsw, chaff, clever, compactor, crankshaft, fine, finer, loosening, nut, nuts, pins, pulled, range, reckon, scratching, standard, stop, thread, threads, tight, tpi, vibration
    • Replies: 2
    • Views: 1,429
    Last Post: 22nd July 2014 03:29 PM
    by Aussie Bruce  Go to last post

    Forum:
    METALWORK FORUM

  3. When did P&N make this set

    Started by woodfast, 1st March 2014 12:19 PM
    2 Pages •
    1 2
    1/4, 3/4, added, bought, box, bsf, condition, die, dies, hope, ideas, make, p&n, pandn, pictures, pieces, recently, set, tap, wooden 15 Attachment(s)
    • Replies: 18
    • Views: 3,219
    Last Post: 2nd March 2014 01:27 AM
    by Combustor  Go to last post

    Forum:
    METALWORK FORUM

  4. Lever locking pliers - slide hammer adapter

    Started by nearnexus, 7th December 2012 05:07 PM
    7/16, adapter, anyones, blessing, bronze, bsf, cheers, design, difference, engineers, gadget, grit, hammer, handy, lever, locking, nice, photo, pliers, project, resign, rob, screw, sheeesh, simple, slide, suitable, taiwanese, teeth, thread 1 Attachment(s)
    • Replies: 2
    • Views: 1,808
    Last Post: 8th December 2012 08:00 AM
    by nearnexus  Go to last post

    Forum:
    METALWORK FORUM

  5. Threading again

    Started by morrisman, 9th December 2011 09:13 PM
    2 Pages •
    1 2
    3/4, bsf, chuck, column, cutting, depth, difficult, explain, fiddling, hss, judge, key, lock, managed, mike, milled, nut, pick, piece, post, progress, putting, removed, rigid, slot, spindle, thread, threading, tight, tool
    • Replies: 18
    • Views: 2,070
    Last Post: 10th December 2011 03:16 PM
    by Michael G  Go to last post

    Forum:
    METALWORK FORUM

  6. "GOLIATH" brand taps

    Started by Kody, 26th March 2011 01:43 AM
    316, 5/8, action, brand, bsf, computer, cos, deck, died, english, forum, goliath, golieth, holes, hss, illness, info, kody, lots, missed, months, quality, stainless, steel, tap, taps
    • Replies: 3
    • Views: 1,531
    Last Post: 26th March 2011 09:04 PM
    by Godzilla98  Go to last post

    Forum:
    METALWORK FORUM

  7. Cutting a 1 1/2 Inch 8 TPI - UN thread

    Started by 19brendan81, 7th June 2010 04:39 PM
    1 or 2, 1/2, brendan, british, bsf, cheers, cutting, data, fine, front, inch, lathe, manual, mentioned, pitch, spindle, standard, thread, tpi, unsure
    • Replies: 11
    • Views: 3,283
    Last Post: 9th June 2010 03:40 PM
    by 19brendan81  Go to last post

    Forum:
    METALWORK FORUM

  8. Work around for the Zyto backplate?

    Started by jmk89, 22nd August 2008 10:30 AM
    11/8, 7/8, adapter, alternatively, backplate, bsf, bsw, called, connect, cut, externally, fitting, internally, loctite, mick, minitech, moyles, myford, nose, pieces, rod, spindle, standard, thread, threaded, tpi, voila, work, workaround, zyto
    • Replies: 4
    • Views: 1,784
    Last Post: 22nd August 2008 11:06 PM
    by Woodlee  Go to last post

    Forum:
    METALWORK FORUM

  9. falcon plane problem - thread sizes

    Started by old_picker, 26th May 2007 07:05 PM
    1/4, ago, avail, bit, bits, bsf, cleaned, couple, cursing, days, falcon, fiddling, fine, guess, guessing, guidance, hoping, jar, job, nice, plane, problem, ran, ruin, screw, shed, sizes, swearing, tap, thread
    • Replies: 4
    • Views: 1,728
    Last Post: 26th May 2007 09:47 PM
    by Dan  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  10. TL 1000 technatool lathe, outboarding?

    Started by ribot, 12th October 2005 02:23 PM
    1000, bsf, direct, faceplate, gippsland, guys, hand, hands, inch, lathe, left, melbourne, outboard, outboarding, relic, technatool, thread, tpi
    • Replies: 3
    • Views: 2,001
    Last Post: 12th October 2005 07:00 PM
    by ribot  Go to last post

    Forum:
    WOODTURNING - GENERAL

Results 1 to 10 of 10