Search:

Tag: 8-10mm

Search: Search took 0.00 seconds.

  1. Steam bending cedar

    Started by Bob Hall, 18th September 2007 06:01 PM
    3 Pages •
    1 2 3
    106, 610mm, 75mm, 8-10mm, aopproximately, art, bend, bending, bit, bob, cedar, cheers, conclusion, curve, dry, gradual, hours, length, mouldings, perfect, process, rebuilding/restoring, set, sharpen, slightly, soft, soften, starting, steam, timber
    • Replies: 32
    • Views: 18,289
    Last Post: 31st December 2018 12:49 PM
    by NCArcher  Go to last post

    Forum:
    TIMBER

  2. New weatherboards are full of knot holes

    Started by Reno RSS Feed, 12th June 2012 04:40 AM
    $$$, 5-10years, 8-10mm, appreciated, builder, comments, diameter;, double, dropped, holes, house, knot, leaving, nowadays;, pre-primed, pretty, queensland, read, renovateforum.com, replacing, riddled, scafolding, standard, story, stuff, thickness, thread, time, trouble, weatherboards
    • Replies: 0
    • Views: 1,453
    Last Post: 12th June 2012 04:40 AM
    by Reno RSS Feed  Go to last post

    Forum:
    STRUCTURAL RENOVATION, ROOFING, DEMOLITION, etc

  3. 3M Microfinishing lapping film

    Started by groeneaj, 13th December 2011 11:18 PM
    8-10mm, andy, cheap, chisels, confusion, cut, drive, eastern, film, float, glass, grit, guys, keeping, lapping, melbourne, method, microfinishing, micron, mind, pretty, range, sandpaper, size, start, suburbs, suggest, supplier, tomorrow, understand
    • Replies: 7
    • Views: 3,488
    Last Post: 18th December 2011 08:24 AM
    by rsser  Go to last post

    Forum:
    SHARPENING

  4. Settings

    Started by ahmmha, 11th June 2011 11:58 AM
    8-10mm, ally, appreciated, brand, butt, butt/fillet, cheers, coming, fillet, horizontal, ipm, links, mig-vertical, mild, notepads, overhead, plate, preferably, remember, scenarios, settings, specific, stainless, steel, stick-, tests, vertical, volts/amps, website, weld
    • Replies: 0
    • Views: 1,206
    Last Post: 11th June 2011 11:58 AM
    by ahmmha  Go to last post

    Forum:
    WELDING

  5. New QCTP - which one?

    Started by markjaffa, 14th November 2009 12:42 AM
    16mm, 24mm, 8-10mm, accuracy, advice, appeals, base, bore, buy/do, current, diagrams, diameter, eager, l2994, larger, lathe, machine, post, qctp, question, quick change tool post, read, recommendations, repeatability, section, sectionapprox, shank/thread, solidity, stud, tool
    • Replies: 3
    • Views: 1,430
    Last Post: 16th November 2009 05:04 AM
    by C-47  Go to last post

    Forum:
    METALWORK FORUM

  6. Asbestos in Plasterboard?

    Started by noideamad, 24th March 2008 11:27 PM
    1982, 50s, 8-10mm, asbestos, board, built, cornice, fibre, hemp, hope, house, initially, internal, kitchen, plaster, plasterboard, powdery, prior, re-plaster, reading, renos, reverse, rough, suggesting, thick, walls
    • Replies: 8
    • Views: 33,361
    Last Post: 7th April 2008 10:09 AM
    by Bloss  Go to last post

    Forum:
    PLASTERING

  7. spalted tamarind vase

    Started by Ironwood, 15th July 2006 01:19 PM
    240mm, 264472644826449, 8-10mm, 95mm, borer, brown, coats, dia, fluke, holes, hut, penetrol, run, spalted, tamarind, test, thickness, vase, wax, wood
    • Replies: 11
    • Views: 2,016
    Last Post: 16th July 2006 01:54 PM
    by ss_11000  Go to last post

    Forum:
    WOODWORK PICS

Results 1 to 7 of 7