Search:

Tag: stator

Search: Search took 0.00 seconds.

  1. I know Matty likes the old Motors

    Started by jgforsberg, 30th April 2016 10:02 PM
    2 Pages •
    1 2
    1200/6, 1890s, 550, add, dates, design, forgot, generator/alternator, ground, knowledge, likes, machine, matty, mica, motor, motors, phase, poll, rare, rings, rotor, rpm, slip, slots, stator, suggested, type, volts, wireu, wound 25 Attachment(s)
    • Replies: 19
    • Views: 9,732
    Last Post: 1st September 2016 11:28 PM
    by Oldbikerider  Go to last post

    Forum:
    ANTIQUE AND VINTAGE MACHINERY

  2. Electric Motor

    Started by robbo37, 9th July 2014 01:05 PM
    2 Pages •
    1 2
    burnt, electric, etectric, holds, motor, separate, stator, time 4 Attachment(s)
    • Replies: 22
    • Views: 2,790
    Last Post: 18th July 2014 09:21 PM
    by jhovel  Go to last post

    Forum:
    METALWORK FORUM

  3. Cleaning stator windings on a grinder

    Started by Bryan, 23rd May 2012 07:39 PM
    air, bench, birthday, bit, cleaning, compressed, dry, dust, fine, giving, grinder, grit, motor, poor, sealed, solvent, stator, sticky, windings
    • Replies: 14
    • Views: 2,700
    Last Post: 24th May 2012 03:52 PM
    by Kraehe  Go to last post

    Forum:
    METALWORK FORUM

  4. electric motor fun

    Started by morrisman, 28th April 2012 05:35 PM
    2 Pages •
    1 2
    3hp, amps, ball, bearings, belt, board, compatible, current, electric, faster, fun, hendey, hit, huge, mike, modern, motor, noise, plate, power, pulley, rewind, rewound, rotation, shaft, size, solid, stator, vfd, whining
    • Replies: 16
    • Views: 3,056
    Last Post: 30th April 2012 06:17 PM
    by morrisman  Go to last post

    Forum:
    METALWORK FORUM

  5. Arboga EM825 motor rewind

    Started by WCD, 9th April 2012 07:55 PM
    2 Pages •
    1 2
    240v, 415v, arboga, coils, dahlander, delta, double, em825, extra, job, low, motor, phase, plan, pole, required, rewind, rewound, risk, speed, speeds, star, start, stator, supply, switched, torque, vfd, winding, windings
    • Replies: 17
    • Views: 5,153
    Last Post: 23rd April 2012 10:10 PM
    by WCD  Go to last post

    Forum:
    METALWORK FORUM

  6. dual voltage AC motors query

    Started by morrisman, 11th April 2012 11:11 AM
    240, 415, apparently, connecting, correct, costs, countries, delta, dual, exhibit, half, impedance, mike, mode, modern, motors, phase, query, question, save, set, standards, star, stator, tapped, terminals, theory, twin, voltage, windings
    • Replies: 3
    • Views: 1,182
    Last Post: 11th April 2012 02:42 PM
    by morrisman  Go to last post

    Forum:
    METALWORK FORUM

  7. Drill Stator rewind

    Started by kenny_10, 22nd October 2010 01:10 PM
    amount, bound, cage, cheers, coil, coils, completed, cotton, drill, effect, equal, insulated, job, ken, leads, longshot, motors, performance, poly, protrude, regular, remove, required, rewind, seal, sharp, stator, tape, unit, varnish
    • Replies: 0
    • Views: 1,550
    Last Post: 22nd October 2010 01:10 PM
    by kenny_10  Go to last post

    Forum:
    GENERAL & SMALL MACHINERY

  8. Reversing the direction of my Belt Sander?...

    Started by Batpig, 12th July 2009 05:35 PM
    3 Pages •
    1 2 3
    armature, belt, brush, brushes, capacitor, coils, combination, commutator, direction, drill, feeds, grey, lever-switch, motor, ozito, photo, power, results, reverse, reversing, runs, sander, simple, spiralling, stator, stator-halves, switch, trigger, wire, wires
    • Replies: 34
    • Views: 12,030
    Last Post: 16th July 2009 03:58 AM
    by gerhard  Go to last post

    Forum:
    HAND TOOLS - POWERED

Results 1 to 8 of 9