- First post-Workbench
- 3 Legged Dinning Table
- Veneer Radial Matching
- North Queensland Chess Board Question
- Help with timber identification please?
- Panel breakdown on short stroke slider
- Is there a "Design" section of the forums?
- Making wooden vise screws
- Straightening aged warped jarrah floorboards
- Expansion Gaps - For Tongue and Groove treated Pine boards
- Timber Advice - outdoor workbench
- How to repair a broken mortise
- Suggestions Needed
- Best way to cut a 7 sided heptagon
- Old weather board and old nails
- Sizing doors for kitchen cabinets
- Bandsaw help blade guides and general set-up for new user MJ343B
- Semi circle hole in wooden handle
- Eucalyptus Lane Poolei, timber characteristics?
- Building these stocks - any tips?
- Internal measurements - Easy way
- Small project last month
- 12" wide belts sander
- Anyone with a large drum sander I can use?
- H4 Laminated Treated Pine Posts
- Commercially available steam generator box in Australia
- S2S tempered masonite/hardboard in Australia
- Inspirational
- Where to place dividers in kitchen cabinets
- How to level a tree branch?
- Hot Stamp Branding Iron for a logo question please!
- Help - is this edge banding any good
- Compound Veneering a waterfall edge
- Trend Air Shield filters
- Makita LS1219 or Bosch GCM12GDL SCMS?
- Hnt Gordon a55 VS Lie Nielsen 4 1/2
- Bending Veneers
- Glue/Sawdust Mix vs Woodfiller
- Craig
- I have a question about Bandsaw mills
- RZ Dust Mask - Valve Caps - ~$28.49AU - Including shipping
- Crubber best brand for use on vise jaws
- Tempered masonite used to be darker. Has it changed?
- Technical beginner, how to make a small support horizontal and stable?
- English Garden Bench Plans Wanted
- Sounds of the productive woodworking workshop (now on CD!)
- I think I found a knot when I got past the rough saw marks...
- LVL Formply?
- Wood stress in riser boards tech question
- Warning - actually bolt your benchtop power tools down
- Higgins and Gifford Banks Dory
- old jarrah floorboards
- Suggestions Please Saw Stop vs Grizzly
- Wood movement
- Introduction to Japanese Tools and Kumiko course
- Wide belt sander / wide thicknesser in adelaide
- Moving to Canberra
- How should I sort this out?
- How to jigsaw in from an outline to account for carpet over ply
- Where to buy a Fret-saw handle local to Bathurst?
- Woodworking equipment assembly
- Tablesaw Blade Sharpening
- Festool Recall (Kapex)
- Dog Sled. No fasteners
- A Table
- Species of hardwood
- Need help identifying this jointer..
- A bit of everything
- Rare earth magnets v A metal detector
- need help to identify timber species
- After some help with my 22-440 sc oscillating drum sander
- What is the best method of applying timber preservative on site? Help assignment ques
- Pantry shelf
- Thicknesser and embedded screw didn't play well together
- Device sought to limit spread if trestle legs
- builders bog
- Drill press recommendations,
- Smoothing concave and convex curves
- Translation Please...!
- Giant Jenga
- Making a large cabinet from melamine (particleboard)
- Mind boggling work - NOT done by me
- Gluing an angled butt joint
- Deciding on a Domino
- Sandpaper to fit ozito
- What is it
- Flat bed sander?
- A few questions about general woodworking
- Plywood Advice
- Is this a good pocket hole jig?
- Problem rip sawing merbau timber decking
- Finished Toolchest Project
- Is everyone closing up
- Eucalyptus plywood.
- Drum Carder
- Fine Woodworking magazine
- igaging Planer DRO
- Stabilising board
- Sanding Belts needing a fix
- What's a good technique for making two boards each perfectly level for gluing togethe
- I think I found Brett's (fencefurniture) answer to a good coffee
- Structural pine from Bunnings?
- Room within a Room Construction
- Using shims to draw bore mortice and tenon
- How to run a straight trench along a long dowel?
- Cut List Software - generate optimised cutouts on sheets
- Table saw belts
- Mesh sanding discs 150mm - Smirdex
- Hi-Fi rack - joining two boxes together with gap
- Storing CA Glue
- Trouble Shooting Splined Bent Lamination
- For those without a tablesaw, but keen with hand tools and room for a tracksaw
- I am new here..., Need advice
- WEN spiral planer v DeWalt
- Getting By Without a Tablesaw
- The workhorse that is a bench, small workshop answer for those with a small space
- Two questions, tables saws and adhesives
- Finishing Question
- Cranked tang chisel?
- "Sysport" Build - And the Three Little Jigs.
- What blade for my new sawstop contractor saw?
- Where to buy plastic honeycomb core
- Workshop tour May 2021
- cutting boards and wood shrinkage
- Edge banding
- CNC Machining Required, 3104 Location
- Bunnings to open specialty tool chain
- Question re using hide glue to make "knock-down" furniture
- Looking for someone who has a wide belt sander in Adelaide
- Perth: Someone to service my thicknesser and possibly Planer
- Camphor laurel
- Ideas to fix f clamp
- Have you guys had this?
- Drawer Slides, Where to buy.
- Speed Cutting Dovetails
- Woodfast original owers
- More than one way to...
- Bed frame hardware
- auto feed for table saws
- Adirondack chairs
- Roller for PU glue application
- Hand Cutting Dovetails - Video
- Looking for advice on what to do with this beam
- Dawn face vice
- Room air filter stop working
- Kitchen Shaker Cabinets - Material & Paint Recommendations
- Garden Bench Restore
- Drop leaf ikea hack work table design help for a novice - chipboard?
- Giving a pallet a new life: Plant and shoe shelf
- Wardrobe Door Construction