- Cast iron plates
- DMT Dia-Flat Lapping plate
- Fluid for waterstones - what do you use??
- choosing bevel angle
- Determine grit of waterstones
- Wet sharpener with CBN -no water
- Dmt diamond plates discoloured after one use
- where do I start.
- Any sharpening services in Brisbane?
- Drill bit sharpening jig ideas and links please
- Sherwood 8' slow speed grinder
- PMV11 sharping let the games Begin [emoji41]
- Sharpening old razor blades
- Power to weight ratio - grinders and cbn wheels
- How sharp is sharp. and the plane pull test
- 1x30" belt sander / grinder - a bad buy
- State of play for Tormek / CBN wheels
- Honing chisels on MDF
- Cannot get a straight bevel to save my life.
- Sharpen an Irwin speedbor Auger drill bit?
- BU Plane blades and the steel ruler trick
- TCT sharpening
- Veritas Grinding Stand and jig
- Veritas Honing Compound v Generic Product
- Problem with Shapton Glass stone 8000 Grit
- Cerax by Suehiro Ceramic Stones
- A "Stone Vice" for sharpening.... A clever idea to look at
- The Unicorn method
- Veritas honing guide skew
- Unicorn Method and plane irons
- New study may lead to better blade steel...
- Sharpening Stainless Double Edge Razor Blades
- Unicorn in depth article
- Tormek BGM100 on bench grinder
- CBN balance
- How to check if diamond plate is flat?
- Does CBN wheel quality differ from one supplier to another?
- CBN, Tormek or both
- Tormek Planer Blade Jig Help
- Bought a Diamond Plate - Any Reason to Keep Waterstone?
- Cheap water stone is that false advertising
- Saw Doctor Training AND you need to be an apprentice before you can do the TAFE cours
- basic setup, what do i need?
- Sharpening bandsaw blades
- Sherwood YF-870
- Eclipse style honing guide advice
- Flattening the backs
- Phone applets for sharpening knives on budget wet grinders
- Sharpening Router Plane Blades
- Economy digital scopes
- Veritas Honing guide II vs Henry Eckert honing guide
- Chagrin Falls Deerlick Oil Stone Co - Oil Stone
- Sharpen Stanley spokeshave 151 blade
- Cutting edge of hollow ground blades short lived?
- Old Tormek SA 250 - motor not working
- Problems with the unicorn method of sharpening
- Using the side of the Tormek SG wheel
- Stanely blade - removing protective film
- How to sharpen & polish a convex chisel?
- Multisharp drill bit sharpener replacement collet
- Mortising chisels
- 24V drill doctor
- Bench covering for sharpening station
- Tragedy and the shattered Shapton
- Sharpening stone/plate that can be used dry and never needing flattening
- Sharpening using a Wetstone
- CBN wheels for a Tormek.
- Sharpening for turners - where to start?
- Is this adequate for sharpening
- Is a T8 that much better than a T7?
- A good polishing stone, for tools and knives - Shapton 2000/4000?
- Scheppach Tiger 2500 advice
- Extracting/minimising metal dust in the workshop for better health
- How to clean a loaded coarse (120 grit) shapton ceramic stone?
- Getting started with grinder for tool sharpening
- How important is the front and side width of CBN wheels?
- Saw topping
- Oil stones what have I got.?
- Grinder balance
- Whetstone selection
- Diamond plates from asia
- So what do you do if you can’t sharpen
- 8 inch wheels and buffs on 6 inch grinder
- Plane iron secondary bevel is not parallel!!
- Sharpening bandsaw blades with chainsaw sharpener
- Drill Bit Sharpening Station
- Horizontal automated water stones.
- Wood by Wright chisel testing
- Would adding a hand wheel to your powered grinder, to make a
- Removing the convexed area ("belly") from a badly convexed chisel
- circular saw blade sharpener Timbecon vs Forestwest
- Sharpening Joiner Blades - Service or DIY
- Veritas side clamping guide
- VICMARC CBN Sharpening Station
- Abrasive to polish plastic
- Re-toothing small tenon saw
- Sharpening advice for planing wiggly Tuart
- Bench grinder CBN wheel runout
- Sharpening Robert Sorby mini woodturning set
- Sharpening flowchart
- Scheppach tiger grinder wheels off centre
- Advice on low/mid budget wet grinders
- Sherwood jigs on Tormek Bench Grinder Mount
- Sharpening a Jimmy Clewes grind on a Tormek
- Pike oilstones
- Waterstones. Something I didn't know
- How do I sharpen forstner bits?
- Bench Grinder Questions
- Jet Wet Sharpener
- Sharpen a convex finger plane blade
- Anyone got information on this stone.
- Sharpening a Card Scraper
- So how bout them Arkansas' eh!
- Stones
- A Proper Studt of Sharpness With All the Data
- Sharpening Dewalt DW735 blades in Melbourne
- First Western Natural StoneI
- Sharpening Stanley No 50 blades
- Power Sharpening Options
- a quick and easy way to test your edge.
- Are these carbide knives?
- Love for washitas and alternatives
- Small Blade Sharpening Jig
- A bit of sharpening sacrilege to brighten your day.
- Sharpening Drill Bits - Michael Fortune
- King waterstone - is there a way to know what I got at a yard sale?
- Grinding Jigs and Camber