- We all have to start somewhere
- Squirrel cage Venting fans
- Cleanspace2
- Dust extraction upgrade at Roy Schack's workshop
- Micronair, anyone used their machine?
- Bag changes
- FC-10 Filter cartridge
- 6''pvc to two or three 4'' outlets
- My Clear vue installation
- What's the best dust mask to use when wearing spectacles?
- Dust collector clogging up.
- cyclone bigger than CVMax?
- How long does it take to "condition" a DC needle felt filter
- What improvement in flow does removing VC filters generate?
- 45 degree takeoff position
- Hose for hand held power tools
- Dust extraction in my new workshop
- Power supply for 3-phase DE when using VFD
- Fibreglass Cyclone Project
- combination machine dust extraction upgrade, port and internals
- Difference between these two dust units
- help with dc upgrade
- How High can it suck?
- New Workshop Setup
- SETTING UP NEW SHED (Air Filters)
- yet another newbie 2hp question
- Clearvue Install
- Push comes to shove. cyclones
- various cyclones design
- slow motor start
- Shop Vac advice for a beginner on a budget.
- Woodfast 3Hp 8 Inch Dual Bag?
- Some general advice on a Clearvue cyclone installation?
- Dust extraction layout ideas wanted.
- Things ya find - no sucky suck!
- Win a FREE cyclone - JordsWoodShop competition
- Wheelie Bin Cyclone?.
- Shouldn't have bought it, experience with low quality PVC
- Commercial/industrial dust extraction?
- Wood Allergies and Toxicity
- What Size Dust Extractor Do I Need ?
- Source for large flexible ducting?
- Air filters
- Dust extraction
- Duct size.
- my cyclone build
- Source of Fibre Drums for Cyclone Dust Collector
- Small Blower construction
- Two 4" ducts vs 6" duct
- Modifications to a "2" HP Dusty
- Source of metal spiral ducting in Melbourne
- Experimenting with a Toolex 2HP dust extractor
- modifying a 3.1m tall dust extractor into 2.7m ceiling height garage
- Principles of Dust Extraction / Management for a new shed
- Extraction layout - Help...
- Why isn't a 100mm dust port 100mm?
- My Very Sloooow Clear Vue Max Install
- Cheap Dusty?
- Cyclone Main Duct
- Alternative Dust Extraction Solution
- Working outside and dust making
- Dust concentrations while drilling wood
- Is this any good?
- Can I use a wet dry vacume for cheap dust extraction.
- Best way to connect two 4" pipes to router table
- Eat My Dust
- Ducting Layout
- Swimming pool hose becomes a DE hose???
- Just to let You Know
- Ducting layout for new shed
- Getting by: What's a baseline for the "average" woodie's shed?
- Dust Extraction for Lathes
- Dust extraction on a drill press
- The balance between Dust Extraction and PPE
- Clear Vue Max owners - source of 44 gallon drums
- Cost of running 225mm mainline ducting for Dust Extractor
- CV - 1800 vs Max
- Beginner attempt at DC - thanks to forum members
- CV1800 Install (Brisbane)
- I May have a good deal
- Shop Vac + Cyclone - Does size of Shop Vac unit matter
- Trend Air Shield Respirator
- blocked pipe
- Sound attenuation (a different approach).
- Adaptor for 100mm dust outlet
- The alan key mystery.
- BMS Clearvue installation
- Filters or lack of Them
- advice on dust extraction system, layouts etc.
- Purchasing a cheap dust extractor
- Help wiring a Fan (pics)
- Replacement Filter Bags
- Safety notice to all clearvue owners
- New setup. Gate location advice please!
- A few questions for the board
- Beijing - BobL's worst nightmare!
- Connector: Branch Angle
- Laguna 14 inch SUV band saw.
- Blast gate position and three 4" outlets from one 6"
- FELDER RL200 and RL250 question
- Bonding PVC Pipe
- Experience with Clear Vue blast gates
- Interesting Concept
- Oneida-air Dust Deputy Kit question please!!
- SCMS dust extraction
- Converting Inches of water to FPM and CFM
- horizontal morticer dust shroud
- ClearvueOz CLOSED?
- Total Tools 3hp Dust Extractor
- Up Grading engine
- Shop vac washable filters worth it?
- Dc purchase
- 12 inch planer dust chute
- Questions about a Hafco DC-45
- Bell mouth from wood for drill press
- BobL should write a book
- Dust extraction strategies for underneath the table saw?
- ShopVac System or Dedicated DC
- Vacuum relief valve needed for Dust Deputy
- 1.5mm plastic sheeting required
- Attacking my Bandsaw...
- Auto on dust extractor?
- Fair deal on 3HP DC
- Large cyclone - premade solutions?
- Metal dust - how bad is it
- Advice needed for large rip saw
- Emptying the dust bin
- New DC advice sought
- PVC Ducting Joint Seals
- Ducting - transitioning from big pipe to smaller pipe at cyclone inlet
- External venting
- location for extraction hood for wide belt sander
- Muffler Bodies
- Ducting, should I reduce the main trunk after divert valve?
- Compound Mitre Saw Dust Extraction
- Free DC systen
- Ducting - do I care if dust drops in horizontal 225mm PVC pipes
- My Clearvue Installation
- Table saw guards and dust extraction for "non-through" cuts?
- HEPA filters
- major woodworking cyclone dusty
- Yep, another call for help with an extraction system design
- connecting 6" (150mm) flexy
- Home made dust collector. A little different
- "Delayed switch off" power control for DCs
- disconnecting PVC fittings
- Invisible Dust question....
- my workshop ducting, completed with photos.
- Fan noises
- ducting and airflow - have I really understood............