- Timber steps - what finish
- Help with T3 MPG10 green
- anti-mould linseed
- Waterproofing timber stairs
- Using undercoats/primers/sealers as top coats
- Oil Finish and Tassie Blackwood
- Sanding sealer for figwood
- Advice / Recommendation on finishing recycled jarrah
- Finish for Laminate WorkBench Top
- steam heat stains on maple
- Oils vs Wax
- Mirror Finish surface for heavy objects like lcd monitor
- finishes you've tried on mango.
- big ugly scar...
- Cut & polishing near edges with sides?
- Drying problem with tung oil.
- Finishing pine table tops - Basic newby questions
- Refinishing of wooden coffee table
- Finish for huon pine.
- Bamboo kitchen bench problem
- Liquid Glass
- Need help to achieve limed finish in Blackbutt
- Preglued iron-on veneers
- Spray Guns!!!
- Entrance door lacquer and stain
- Painting Metal
- Staining burls
- wax and finishes
- Going up through grits before polishing polyurethane
- Finishing for a Park Bench
- How to keep the "industrial" look when finishing
- rough patterns in varnish.
- Fish outta water...with a blackwood mantle :)
- Online Timbermate wood filler supplier
- Japanese Lacquering
- dining table
- shou sugi ban, tung oil , shellac, epoxy. nothing is off limits to me.
- pearlescent finish
- Clear epoxy over shellac?
- outdoor bird feeder finish
- Specific questions about shellewax cream on canned Poly.
- Painting kids toys - perfect finish?
- How would this be for an outdoor timber finish (or table/bench tops)?
- Finishing process - OK or flawed?
- Stripping tint from decking
- Olfaction - Finishes so good they should be released as a cologne
- Adventures in matte 2k paint.
- Parker dining table stripping and refinishing
- Decking upside down deck timber stained
- Where do I go from here?
- How to finish coarse grained timber?
- Finishing inquiry
- Canned Shellac confusion
- my favourite prooftint stains no longer available :(
- Sandpaper Question
- Finish for an IKEA Birch butchers block benchtop
- Jarrah burl - how to make it nice, shiny etc?
- High gloss polish on vanish
- Good finish for brass escutcheon plates - will shellac take/hold?
- DIY stains - artists oils
- Help needed with Spotted Gum Outdoor Table finish..
- Plexiglas as a timber stabiliser
- Best finish for black bean timber.
- Finish for one indoor & one outdoor Blackbut slab table
- Help with project - turning a river red gum timber slab into a bathroom vanity top
- Can I leave my piece natural without a finish?
- Paint Brush maintenance - wire brush and flea comb and a gong for Minwax Lacquer
- Muddy shellac
- HELP With Table! Please!
- Retaining "pinks" in Camphor
- Best finish that won't discolour a desk top
- Sealing in patina
- Square profile skirting
- Finishing walnut veneer
- bureau bookcase
- wrinkly varnish
- What is the best way to achieve an open grain finish on a pine board
- nitrocellulose
- Scandinavian oil wiping application
- ROS finish problem
- Finishing white painted furniture
- 2K matt clear on Tassie Oak
- varnish or what
- Blackwood dining table finish
- Three Tables - help required
- CA + Paper Towel + Finger
- Spray Guns... Nozzle Size???
- Refinishing huon
- Staining black
- rifle stock finish.
- Finishing Jarrah slab
- How to get pine to look like baltic pine
- Merbau sanding and sealing how much it should cost
- Using Clear Epoxy Coatings
- "Sticky" jarrah table surface
- Spotted Gum Tabletop Finishing
- Polyurethane over epoxy resin
- Can't get Mirror Finish with foam sanding block
- Caustic Soda used as paint stripper?
- Traditional wax
- What finish for Tassie Oak Dining Table?
- Do indoor Cut & Polished Finishes need to be Waxed for protection?
- Powder coating hinges? DIY available?
- Many Thin coats of canned clear reduces Gloss w/ Cut & Polish?
- Oil or timber stain finish for western red cedar shutters ?
- Water rubbing compound and finishing spirit.
- Spraying Oil paints - is the Graco Truecoat any good?
- Beeswax and raw linseed oil
- Sanding and finishing a Jarrah side table
- ironbark floor
- Well.. I'm in a pickle
- Crazed
- wrong finish
- Clear for redgum recommendation?
- Restoring and finishing an oak pedestal desk
- Help with prep before staining
- Finish for brushbox
- Tung Oil finish on Blackbutt
- Elm Dining Table
- Kauri Pine Coffee Table
- Sanding block for Hook & Loop abrasives
- An excellent source of info on abrasives
- Aussie oil on camphor laurel?
- Solid Solutions 606 Resin
- Disintegrating Gloves
- Help in sealing Marri
- Staining and Finishing Edge-Glued Clear Pine Panels
- Green or natural check out the pics
- A new discovery
- Wattyl Craftsman Natural Teak Oil over poly???
- How to finish huon pine vanity bench tops?
- Advice for restoring a 100 yr old black Ronisch Piano
- How do I make Red Cedar look grey
- 2 part bleach
- WOP finish problem
- feast and watson tung oil
- Sanding sealer on red-brown cedar
- Finishing and... Insects.
- Varnish over prefinished benchtop?
- Darkening QLD Maple
- Gel coat finish
- Finishing advice for Tassie oak built-in bench top
- minwax helmsman teak oil
- mpaul
- Blisters with Varnish on Cedar Outdoor Cedar Tabletop
- Finishing Table
- Options for a ply table top?
- Using high volume Spary Gun on small Capacity Compressor
- Annoyed, need to spend another $21.80
- Finishing courses in Melbourne?