Router Options

[rachal73]

Hi. Im also wondering your thoughts on the below models...

Triton® 2400w / 3.2hp Dual Mode Precision Router : CARBA-TEC (http://www.carbatec.com.au/triton-2400w-32hp-dual-mode-precision-router_c20847)

or

Triton® 2400w / 3.2hp Dual Mode Precision Router : CARBA-TEC (http://www.carbatec.com.au/triton-2000w-275hp-dual-mode-precision-router_c20847)

I'm not too concerned about the cost as I want to get something that is going to last a long time.

Any thoughts would be ideal.

Also, both of these routers have collet - 1/2" - includes 1/4" reducer. Is this referring to the size of the shank for the bits?

Thanks in advance for anyone who replies.....

Rachal

[Scott]

The two models you've highlighted are exactly the same. Based upon this information, I'd go for the Triton 2400W / 3.2hp Dual Mode Precision Router :D

[Superbunny]

Hi. Im also wondering your thoughts on the below models...

Triton® 2400w / 3.2hp Dual Mode Precision Router : CARBA-TEC (http://www.carbatec.com.au/triton-2400w-32hp-dual-mode-precision-router_c20847)

or

Triton® 2400w / 3.2hp Dual Mode Precision Router : CARBA-TEC (http://www.carbatec.com.au/triton-2000w-275hp-dual-mode-precision-router_c20847)

I'm not too concerned about the cost as I want to get something that is going to last a long time.

Any thoughts would be ideal.

Also, both of these routers have collet - 1/2" - includes 1/4" reducer. Is this referring to the size of the shank for the bits?

Thanks in advance for anyone who replies.....

Rachal


I think you mean the 2400w and the 1400w Triton routers i.e. the big one for the router table and the smaller one for hand held use.
Yes they are good and the collet is referring to the shank of the router bit.

SB

[rachal73]

Thanks to you both and yes I was referring to the smaller one and the larger one.Thanks again for replying... Appreciate it.

[simops]

Rachal,

I have the larger Triton 3hp model TRB001 mounted to an aluminium router plate that is then mounted to a router table top. This, I believe, is the minimum HP for table mounting. Also it has a handle that slots into it for raising and lowering the router from the top of the table .... Very useful.

Get this router you won't be disappointed. Get a decent router table and fence and you're on your way.

And yes it comes with both 1/2 and 1/4 inch collets. When buying bits go for 1/2 inch whenever possible. It will be stronger and have less vibration making for better cuts.

Any other questions feel free to ask.....

MT

[rachal73]

Rachal,

I have the larger Triton 3hp model TRB001 mounted to an aluminium router plate that is then mounted to a router table top. This, I believe, is the minimum HP for table mounting. Also it has a handle that slots into it for raising and lowering the router from the top of the table .... Very useful.

Get this router you won't be disappointed. Get a decent router table and fence and you're on your way.

And yes it comes with both 1/2 and 1/4 inch collets. When buying bits go for 1/2 inch whenever possible. It will be stronger and have less vibration making for better cuts.

Any other questions feel free to ask.....

MT

Thank you so much MT. From what I've been reading the model you suggested is the one I'll be buying. I also got Triton RSA300 Router Stand, Triton RTA300 Router table top, Triton BJA300 Biscuit Joiner attachment
+ Plus associated parts as shown. (Found on Gumtree for $200.... and picking up wednesday....).

It's the router bits that are confusing. So many things I want to do and try but I've read that buying the best ones will last and last so I'm going to get them at a later date...

I have so many questions but I don't want to take advantage or annoy any of you lovely people,so if anyone has any links to router bit profiles and which ones do what then I'd appreciate the time. I'm interested in doing a course but can't find anything that suits....

I'm so excited about this so thank you so much for everyone's patience and time in replying...

Rachal

[rachal73]

Rachal,

I have the larger Triton 3hp model TRB001 mounted to an aluminium router plate that is then mounted to a router table top. This, I believe, is the minimum HP for table mounting. Also it has a handle that slots into it for raising and lowering the router from the top of the table .... Very useful.

Get this router you won't be disappointed. Get a decent router table and fence and you're on your way.

And yes it comes with both 1/2 and 1/4 inch collets. When buying bits go for 1/2 inch whenever possible. It will be stronger and have less vibration making for better cuts.

Any other questions feel free to ask.....

MT

MT

You mentioned a fence for the router table.I'm guessing this is used a guide / stop of sorts... For the triton router and table which fench would you suggest or does the table already come with it... Sorry to sound so dumb but I've never been one to do something wholeheartedly and if I get it right now then hopefully I won't have any issues.

Thanks again for your help.

R

[Treecycle]

I believe MT is referring to a dedicated router table such as this one (http://www.carbatec.com.au/kreg-precision-benchtop-router-table_c20830). The fence allows you to guide your timber past the cutter, and is a must if you don't have bearing guides on your router bits. You can also use it to adjust how much of the side of the bit engages into your timber
You will have a fence on your Triton, but it will be fairly low. It will still do the job, but maybe not as robust or as accurate.

[malb]

Rachel, your guess about the fence is fundamentally correct, it is used as a guide and to set the position or width of a cut. I am not a Triton table user so I am not familiar with what comes standard with them, but at its most basic, a fence could be a straight smooth piece of timber fixed to the table with a reliable pair of clamps. At their most exotic, you are looking at things like the INCRA LS series and similar which offer instantly repeatable precion adjustments, and microadjustability.

A good source of info for table routing is Routerworkshop.net (http://www.routerworkshop.net/), the website for a older series of routing TV programs. For a few dollars a month via Paypal, they make downloadable versions of their program available one episode per week. This features handheld and table based routing utilising a basic table setup and jigs that they used to supply. Unfortunately they have retired from the table and jig supply business, and some of the projects are dated style wise, but the techniques they use are translatable to most systems other than the INCRA mentioned above. There is also an associated Router Workshops (http://www.routerforums.com/) forum with discussion on all aspects of routing.

With relation to bits, there are a number of styles of bit depending on what task you need to do. Some have bearings at either the shank end or tip end, and are intended for following a pattern or template, or cutting a profile into a square finished edge. Others are non bearing, and are able to be used for plunge cutting which is important for interupted or stop start cuts like mortices. There also special purpose bits for dovetailing, clot cutting etc. Here (http://www.apworkshop.com.au/html/print_catalog.html) is a web page to access bit information for a leading Australian router bit manufacturer, and there is some info for CMT and home brand bits in the Carbatech catalogues.

Hope this helps, feel free to come back for more specific info, thats why we are here.

[rachal73]

Rachel, your guess about the fence is fundamentally correct, it is used as a guide and to set the position or width of a cut. I am not a Triton table user so I am not familiar with what comes standard with them, but at its most basic, a fence could be a straight smooth piece of timber fixed to the table with a reliable pair of clamps. At their most exotic, you are looking at things like the INCRA LS series and similar which offer instantly repeatable precion adjustments, and microadjustability.

A good source of info for table routing is Routerworkshop.net (http://www.routerworkshop.net/), the website for a older series of routing TV programs. For a few dollars a month via Paypal, they make downloadable versions of their program available one episode per week. This features handheld and table based routing utilising a basic table setup and jigs that they used to supply. Unfortunately they have retired from the table and jig supply business, and some of the projects are dated style wise, but the techniques they use are translatable to most systems other than the INCRA mentioned above. There is also an associated Router Workshops (http://www.routerforums.com/) forum with discussion on all aspects of routing.

With relation to bits, there are a number of styles of bit depending on what task you need to do. Some have bearings at either the shank end or tip end, and are intended for following a pattern or template, or cutting a profile into a square finished edge. Others are non bearing, and are able to be used for plunge cutting which is important for interupted or stop start cuts like mortices. There also special purpose bits for dovetailing, clot cutting etc. Here (http://www.apworkshop.com.au/html/print_catalog.html) is a web page to access bit information for a leading Australian router bit manufacturer, and there is some info for CMT and home brand bits in the Carbatech catalogues.

Hope this helps, feel free to come back for more specific info, thats why we are here.

Hi Malb,That's awesome information thank you. I'm not entirely sure about the fence yet until I pick up the table wednesday but please beware that if I need any help I'll annoy you all.lol

The router bits are amazing, and I'll be using the links you sent through for sure.

Hope you all have a lovely christmas with family and friends and that santa brings some yummy tools for you..

R

[Superbunny]

Rachal73, I find for quality bits, amazon is your friend. Only buy the quality name brands, they can be expensive if you buy locally. And yes, only buy 1/2 inch shank bits. Mcjing a sponsor of this forum sell reasonable quality bits at a fair price with quick delivery.


SB

[rachal73]

Rachal73, I find for quality bits, amazon is your friend. Only buy the quality name brands, they can be expensive if you buy locally. And yes, only buy 1/2 inch shank bits. Mcjing a sponsor of this forum sell reasonable quality bits at a fair price with quick delivery.


SB

Thanks SB. Will check out Mcjing..... and amazon.

R

[Treecycle]

Another good source for reasonably priced bits is Bits Below Cost (http://www.bitsbelowcost.com/). Range is not vast, but they are good quality and good pricing. Best to buy as many as you can in one transaction as the price for delivery is the same for one or many bits.