PDA

View Full Version : Symtec 1500 specs



TomBWC
1st January 2017, 08:34 AM
Happy New Year from a brand new forum member in USA.
I am using "Reply" post to this thread because the general title is "SYMTEC 1500" although the posts have been mainly concerned with purchased and availability/cost, I did not see a recent
"open" thread/post which stated technical data of the machine or cutting tools etc.
I'm searched the Symtec threads for technical data on the model 1500 with limited success. If I should start a new post rather than continue here, please reply.
My son purchased a 1500 here in USA a few years back at a tool/equipment auction and it has seen very limited use by us because we are mainly busy with our Home Improvement business. Now I will be doing woodturning as spare time allows. Woodturning tools included with the used lathe were very few and random. Because the auction did not include the original cutting tool and stand, we are currently limited to conventional tool rests and tools. (More on that in a later post).
Please excuse my "beginner status" but I am doing my best to learn both the specialized woodturning craft and also language terms from your "down under" side of the globe. I do not intend to offend y'all, so please be gracious. I have an Associate degree in Engineering so I understand Imperial vs, Metric measurement standards, and because we have a "shop" for our business with saws and planers etc. I am no stranger to cutting wood, but the more difficult learning curve is your sense of humor!
I have just ordered a new NOVA 50MM chuck and I need to order the correct spindle adapter/insert. I am seeking confirmation that the "front" spindle (right side of the head stock) is 30MM and 3.5 pitch. I obtained these specs from the SYMTEC Owners Operating Handbook.
http://symtecwoodturners.weebly.com/symtec-handbook.html<strike></strike>
Page 4&5 of the handbook (items 1.6) is a chart of specifications including the Spindle data.
Using a Vernier caliper I verified that the spindle is 30MM diameter, but I do not have the thread pitch tool to measure 3.5 pitch.
I have contacted Teknatool and downloaded their FAQ "Insert/adapter listing" document. It lists insert - IQNS Insert Q as M30x3.5 but they are unfamiliar with the Symtec lathe specifically. If anyone can verify the 1500 requires Teknatool Insert Q it would be helpful.
Thank you for your assistance.
Tom

joe greiner
1st January 2017, 04:37 PM
You only need a thread pitch tool to measure a mystery thread. You can actually verify yours thus:

Press a piece of paper against the threads to imprint/crease several threads. Standard pitches for M30 are 3.5mm, 2mm, and 1.5mm. Multiply each of those values by the number of threads imprinted, and measure against the length of the creased region. One of the measurements should match.

Woodturning is an international sport, so you probably won't have trouble with the language.

Your learning curve will be gentler if you join a local club, and woodturners are quite generous with knowledge. The AAW has a directory of chapters sorted by state, here: Find a Chapter - American Association of Woodturners (http://www.woodturner.org/?page=Chapters)

Cheers,
Joe

Interwood
1st January 2017, 05:12 PM
Hi Tom,

There is now a Symtec Wood Lathe group on facebook. The link below will take you to the group. The Group Administrator manufactured the Symtec Wood Lathe under license from the Australian Company in Singapore. He set the group up to provide information to people such as yourself.

https://www.facebook.com/groups/585529804967300/

I hope that you get the information that you need to fully enjoy the potential of your Symtec Wood Lathe.

Best regards,

Chris

Paul39
3rd January 2017, 12:39 PM
I was curious about the Symtec and found this:

http://m4usiteimages.s3.amazonaws.com/images_user/pdfs/82/277082/brochure.pdf?t=1459125852

http://www.woodworkforums.com/f8/technical-help-legendary-symtec-wood-lathe-owner-147064



Symtec 1500 vs Record 36x30 lathe (http://www.woodworkforums.com/f155/symtec-1500-vs-record-36x30-lathe-113983) By rev in forum GENERAL & SMALL MACHINERY


Replies: 5 Last Post: 3rd Mar 2010, 01:46 AM



symtec lathe (http://www.woodworkforums.com/f8/symtec-lathe-89275) By ividak in forum WOODTURNING - GENERAL


Replies: 2 Last Post: 13th Feb 2009, 06:05 AM



Symtec lathe (http://www.woodworkforums.com/f8/symtec-lathe-77754) By WBruce in forum WOODTURNING - GENERAL


Replies: 7 Last Post: 24th Aug 2008, 04:56 AM



Symtec Wood Lathe Users (http://www.woodworkforums.com/f8/symtec-wood-lathe-users-64) By Peter Gibbs in forum WOODTURNING - GENERAL


Replies: 7 Last Post: 18th Jun 2005, 07:01 AM

lozkc83
4th January 2017, 12:29 AM
http://uploads.tapatalk-cdn.com/20170103/0de24d407297e5f075dbeabd58b0b0c7.jpg


Sent from my iPhone using Tapatalk

lozkc83
4th January 2017, 12:31 AM
I do have all the manuals and instructions booklets if this is what you are looking for


Sent from my iPhone using Tapatalk

TomBWC
6th January 2017, 10:18 AM
You only need a thread pitch tool to measure a mystery thread. You can actually verify yours thus:

Press a piece of paper against the threads to imprint/crease several threads. Standard pitches for M30 are 3.5mm, 2mm, and 1.5mm. Multiply each of those values by the number of threads imprinted, and measure against the length of the creased region. One of the measurements should match.

Woodturning is an international sport, so you probably won't have trouble with the language.

Your learning curve will be gentler if you join a local club, and woodturners are quite generous with knowledge. The AAW has a directory of chapters sorted by state, here: Find a Chapter - American Association of Woodturners (http://www.woodturner.org/?page=Chapters)

Cheers,
Joe


Joe, thank you very much for the easy method of measuring the spindle pitch. I measured 6 threads over 21mm length so that verifies 3.5mm pitch which I expected.
Secondly, I located a local chapter of AAW which meets 1/month at a location about 20 miles from me. I will contact them and hopefully attend this months meeting to how they function. Their website displays some talented turning artwork and other woodworking techniques that I can learn much from. So, I'm along my way now to improved turning, better for your help.

TomBWC
6th January 2017, 10:56 AM
Hi Paul, Thanks for your time and effort to locate 7 relevant threads/links. I had seen most of the earlier posts on this forum in my searching previously. But your effort here makes it easier for myself and others. I see your no rookie to helping others.

TomBWC
6th January 2017, 11:05 AM
This Specifications page is much easier to read than the "Specifications" data in table form in the owners handbook. Same data, just easier to read here. The spindle data displayed sideways in the on-line version of the manual I was looking and the format was not user friendly (each column was on a different page). Thanks for being a tech savvy and linking this photo.

TomBWC
6th January 2017, 11:37 AM
I don't believe I need booklets or manuals at this time because it was only the spindle size that I needed to verify in order for me to obtain the correct chuck adapter/insert. Mission accomplished on the spindle.
I don't have the Symtec Tools (like the Tool Jig etc.) that the manuals you have describe. The only "Symtec" tool I have now that survived mostly-intact (we bought the lathe at auction) seems to be the Steady Rest. So, I'm just "wingin-it" as they say. Hopefully you can share the booklets with a needful owner who can use the lathe as intended. Thank you for sharing your "originals" resource.

KBs PensNmore
6th January 2017, 11:40 AM
Hi Tom,
Welcome to a top forum. I've a Symtec 1500 as well, any chance of a list of items that you're missing. I have a few parts/copies of items you may be interested in. Postage would be a killer because of the weight factor, but I can make detailed drawings of components you may require and get someone there to fabricate/machine the parts for you. I mainly use my lathe as a free hand machine rather than a copier. Should you have any questions, please feel free to ask here, or PM me.
Regards
Kryn

unbox86
13th June 2019, 03:36 PM
G'day Tom how's it going? Would you have images/diagrams with working dimensions for router spiral attachment?

choof
28th August 2019, 07:04 PM
[QUOTE=lozkc83;1999289]I do have all the manuals and instructions booklets if this is what you are looking for

Hi , a mate has just acquired 1500 and is looking for a manual do you have or a link to get one thanks Choof