Dalboy
22nd February 2018, 04:36 AM
I thought I would start a new thread for this one and have included a short W.I.P. to go with it.
I think this one turned out better than the first as the back does not stick out as far as it did with the first one.
First some of the second completed turning. I did notice the two knots which could have been a bit embarrasing if they ended up in the wrong place so I was careful to locate them at the back.
430208430209430210430207
I hope some will find this useful. And if I have missed anything please shout out I am only human
I started this with a piece of Yew branch that was about 10" long and 2 3/4" diameter this is not critical as measurements can be altered to suit yourself.
At each point along the turning I sanded and applied a sealer before moving on to the next section some sections ende up being sanded and sealer applied more than once.
I marked centres at both ends then at one end only drew a line through the centre and made a mark 3/8" either side of the centre along the line
430204
I placed the blank between centres and formed a chucking point, you will notice this has a slight radius to this as to allow for movement when locating the piece on the various marks later on
430203
While it is between centres I turned the skirt and body this is all done with the tailstock on the centre mark
430206
A quick apology here I forgot to take a photo but used the next one to show what I was doing
You can either place the turning in a chuck at this point or leave the headstock drive with what you started with I am using a steb type centre here. Just a note if you are using the chuck this is where the small radius come into play as you will need to loosen the chuck when moving between centres at the tailstock end and then re-tighten.
Moving the tailstock to position one on the end now turn the body again taking it down to the intersection with the skirt being careful not to catch the skirt with your tool. Now sand this part as you will see two lines running along the body which will need to be blended to the first turning.
430205
Now move the tailstock end to position two and turn the top of the breast area and also the neck remember the neck will need to be small enough for the head in the next step. Because you are using various centres you can always come back to this stage when you turn the head later if you find the neck is too thick so better to make it too thick than to thin.
430211
Now return the tailstock to the true centre to turn the head and the start of the domed top. Once this is done again sand and blend the nech into the head
430201
Once you are happy with the head and with the piece in the chuck part off the waste at the top and tidy up the top dome shape of the head. The reason I made this a dome shape is that when the hat is turned it can be positiond at whatever angle suits you.
430212
Finally I cut a small foot to lift the whole thing a little this is optional
430202
The last piece to turn is the hat which I will leave up to you as to size.
430214430213
At this point I completed the finish before gluing the hat to the body
I think this one turned out better than the first as the back does not stick out as far as it did with the first one.
First some of the second completed turning. I did notice the two knots which could have been a bit embarrasing if they ended up in the wrong place so I was careful to locate them at the back.
430208430209430210430207
I hope some will find this useful. And if I have missed anything please shout out I am only human
I started this with a piece of Yew branch that was about 10" long and 2 3/4" diameter this is not critical as measurements can be altered to suit yourself.
At each point along the turning I sanded and applied a sealer before moving on to the next section some sections ende up being sanded and sealer applied more than once.
I marked centres at both ends then at one end only drew a line through the centre and made a mark 3/8" either side of the centre along the line
430204
I placed the blank between centres and formed a chucking point, you will notice this has a slight radius to this as to allow for movement when locating the piece on the various marks later on
430203
While it is between centres I turned the skirt and body this is all done with the tailstock on the centre mark
430206
A quick apology here I forgot to take a photo but used the next one to show what I was doing
You can either place the turning in a chuck at this point or leave the headstock drive with what you started with I am using a steb type centre here. Just a note if you are using the chuck this is where the small radius come into play as you will need to loosen the chuck when moving between centres at the tailstock end and then re-tighten.
Moving the tailstock to position one on the end now turn the body again taking it down to the intersection with the skirt being careful not to catch the skirt with your tool. Now sand this part as you will see two lines running along the body which will need to be blended to the first turning.
430205
Now move the tailstock end to position two and turn the top of the breast area and also the neck remember the neck will need to be small enough for the head in the next step. Because you are using various centres you can always come back to this stage when you turn the head later if you find the neck is too thick so better to make it too thick than to thin.
430211
Now return the tailstock to the true centre to turn the head and the start of the domed top. Once this is done again sand and blend the nech into the head
430201
Once you are happy with the head and with the piece in the chuck part off the waste at the top and tidy up the top dome shape of the head. The reason I made this a dome shape is that when the hat is turned it can be positiond at whatever angle suits you.
430212
Finally I cut a small foot to lift the whole thing a little this is optional
430202
The last piece to turn is the hat which I will leave up to you as to size.
430214430213
At this point I completed the finish before gluing the hat to the body