MWF FEED
15th September 2020, 10:00 PM
These are some wheel spacers and dust covers I made. Spacers are stainless with ally dust covers pressed in place. The speedo drive is replaced with a stainless spacer with ally dust cover, going to use an electronic speedo instead, if I can find one.
I also removed the caliper mount on the left slider and the lower mudguard mounts, grond them down smooth and polished them.
Hub was chucked, flanges evened up and casting bridges straightened.
The disk was given some lightning holes and the edge polished, the disk mount bead blasted and stainless fasteners polished and fitted along with sealed bearings.
Rim was polished, just have to buy some stainless spokes, polish them and spoke it up.
Attached Images
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_46_57_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388670&d=1600162619) (179.6 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_55_14_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388671&d=1600162658) (131.0 KB)
https://metalworkforums.com/images/attach/jpg.gif hub2.jpg (https://metalworkforums.com/attachment.php?attachmentid=388675&d=1600163528) (176.4 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200828_14_42_08_Pro (2).jpg (https://metalworkforums.com/attachment.php?attachmentid=388676&d=1600163635) (195.5 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200828_14_42_41_Pro (2).jpg (https://metalworkforums.com/attachment.php?attachmentid=388677&d=1600163663) (180.5 KB)
https://metalworkforums.com/images/attach/jpg.gif 35.jpg (https://metalworkforums.com/attachment.php?attachmentid=388678&d=1600164053) (126.0 KB)
https://metalworkforums.com/images/attach/jpg.gif sliders2.jpg (https://metalworkforums.com/attachment.php?attachmentid=388673&d=1600163385) (192.5 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_55_28_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388672&d=1600162711) (130.6 KB)
Read the full thread at metalworkforums.com... (https://metalworkforums.com/showthread.php?t=205635&goto=newpost)
I also removed the caliper mount on the left slider and the lower mudguard mounts, grond them down smooth and polished them.
Hub was chucked, flanges evened up and casting bridges straightened.
The disk was given some lightning holes and the edge polished, the disk mount bead blasted and stainless fasteners polished and fitted along with sealed bearings.
Rim was polished, just have to buy some stainless spokes, polish them and spoke it up.
Attached Images
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_46_57_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388670&d=1600162619) (179.6 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_55_14_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388671&d=1600162658) (131.0 KB)
https://metalworkforums.com/images/attach/jpg.gif hub2.jpg (https://metalworkforums.com/attachment.php?attachmentid=388675&d=1600163528) (176.4 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200828_14_42_08_Pro (2).jpg (https://metalworkforums.com/attachment.php?attachmentid=388676&d=1600163635) (195.5 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200828_14_42_41_Pro (2).jpg (https://metalworkforums.com/attachment.php?attachmentid=388677&d=1600163663) (180.5 KB)
https://metalworkforums.com/images/attach/jpg.gif 35.jpg (https://metalworkforums.com/attachment.php?attachmentid=388678&d=1600164053) (126.0 KB)
https://metalworkforums.com/images/attach/jpg.gif sliders2.jpg (https://metalworkforums.com/attachment.php?attachmentid=388673&d=1600163385) (192.5 KB)
https://metalworkforums.com/images/attach/jpg.gif WIN_20200915_15_55_28_Pro.jpg (https://metalworkforums.com/attachment.php?attachmentid=388672&d=1600162711) (130.6 KB)
Read the full thread at metalworkforums.com... (https://metalworkforums.com/showthread.php?t=205635&goto=newpost)