PDA

View Full Version : Router Lathe??



JackoH
6th July 2000, 12:21 PM
Please could anyone tell me where I could obtain a Router Lathe suitable for the home hobbyist ?
I understand that these things were quite popular some years ago. I believe there was a company making them in West Oz , also an American manufacturer called Vermont Tools. Any info. greatly appreciated.
John H.

John Saxton
6th July 2000, 08:37 PM
G'day John,I managed to get hold of one of these a few years back through Power Tools and Machinery in Bayswater Perth
I had a bit of a win because they had had it on the floor for a while and let me have it at cost when I approached them,I think I paid around $300 for it. It came with very little paperwork and had no brand name so I cannot give you it's origin.
Perhaps you could try contacting the above to see if they still have a source for it. I do Know that they are not WWW friendly at this point in time.Their ph# is 08 9272 3844 should you require it.
Hope this helps
Cheers

------------------
Johnno

[This message has been edited by John Saxton (edited 06 July 2000).]

JackoH
7th July 2000, 05:44 PM
Thanks for the info. Johnno. Iwill ring Perth forthwith, or sooner ! Will let you know if I have any luck.
Regards John.H.

Roly
7th July 2000, 06:47 PM
Some time ago I traced the original manufacturer in the states who used to do a bit of advertising. He stated in a quite curt manner that the tool had been taken of the market and was no longer manufactured.

I remember some years ago seeing an article in "FINE WOODWORKING" that described a shopbuilt router lathe. Although I have searched and searched I can't find the original article. Should you come across it however, I would appreciate its location etc because it has long been my ambition to purchase or make a router lather. I hope this helps a little bit.

Roly

Richard
11th July 2000, 03:07 PM
John, Check out a book called "Router Magic" by Bill Hylton. Gobs & Gobs of good stuff, including a sturdy router lathe.
Book is 45.95 (before GST that is) but well worth it !!
Good Luck

Richard
11th July 2000, 03:11 PM
The book can be found at Woodworks Book & Tool Co. http://www.thewoodworks.com.au
Sorry for leaving this part out !!



[This message has been edited by (edited 11 July 2000).]

Croz
13th July 2000, 06:34 PM
A while ago I found an idea in an American Wood (?) magazine which you might be interested in trying.

This "lathe" consisted of a long L shaped fence which was mounted onto the router table. The piece of timber to be turned, then had disks screwed to each end. The fence had adjustable stops mounted at each end to restrict the lateral movement.

To operate, you manually set the depth of cut & positioned the fence so it was centred on the work piece. You then manually slide the piece of work back & forward over the cutter while rotating the work piece.

A cove or similar bit was used for roughing down & more decorative bits used for more traditional turned effects.

Note on use of the disks at each end:
- same size disks produced a circular piece,
- different sizes produced a taper,
- shapes such as squares & pentagons could also be used. This is handy for fluting table legs etc with a vee or straight bit.

It is easily made (that said it is still on my to try out list) & appears to be quite versatile.

If you're interested, I'll see if I can dig up the relevant magazine.

Croz.

JackoH
14th July 2000, 01:21 PM
Thanks to everyone for all your help. Is'nt it great to have a bulletin board like this with asuch a wealth of experience at your finger tips, so to speak. Ufortunately I am not having a grat deal of success in my quest for a router lathe, but will keep trying. Johnno, the Perth company were less than helpful in that the person I spoke to, (after 3 non retuned phone calls) did'nt semto know orwant to, what I was talking about. I may have to resort to making my own as you suggest Coz, although I doubt my ability to do this since apprentice really does describe me. Also show me a part funded pensioner who has lots of money and I will show you someone who's fiddling the system!
Still, as they say :-,
nil desperandum,carborundum. or somesuch! John H.

JackoH
14th July 2000, 01:31 PM
I've just discovered with pride,that I'm now a FULL MEMBER!
But I can assure you that my woodys' apprenticeship has a fair way to go, as has my word processing ability!
John.H.

John Saxton
14th July 2000, 01:45 PM
G,day John,I will try my local bloke here as he is sub-branch to the parent company in Perth and a lot more helpful.If I meet with any success then I'll naturally get back to you.It surprises me that with the interest in this tool that there is'nt a more considerable profile within the market place.
Cheers

------------------
Johnno

[This message has been edited by John Saxton (edited 14 July 2000).]

John Saxton
14th July 2000, 02:37 PM
John check this site out and you will get the Trend site in the U.K.and all the relevant info on the Routerlathe,just scroll down on the FULL PRODUCT LISTING arrow until you find what you are looking for. www.trendm.co.uk (http://www.trendm.co.uk)

Cheers have a good day and hope this helps http://ubb.ubeaut.com.au/ubb/biggrin.gif

------------------
Johnno

John Saxton
15th July 2000, 06:33 PM
John-- I have e-mailed Trend in the U.K. and they replied that their Australian agent is MIK INTERNATIONAL in Burnside South Australia.
Their e-mail is [email protected]
Trend carry the Routerlathe,I have seen it on their website so you should be able to access it through the above.
Cheers and hope this helps you out. http://ubb.ubeaut.com.au/ubb/smile.gif

------------------
Johnno

RETIRED
16th July 2000, 12:04 AM
Gooday.

John, cut this out or I might become redundant. http://ubb.ubeaut.com.au/ubb/wink.gif

------------------
Ian () Robertson
"We do good turns every day"

John Saxton
16th July 2000, 08:57 PM
,In my book you could never become redundant.

You do many a good turn every day!!

Cheers http://ubb.ubeaut.com.au/ubb/cool.gif

------------------
Johnno

JackoH
1st September 2000, 05:08 PM
To All of Youse. I thought it was about time to bring you up to date with the "Great Router Lathe Search"! After a lot of searching and to cut a long story short I have ordered a machine direct from Trend Ltd in England (By the Way they have a great site on the net with lots of free downloads)They were very helpful., moreso than their Aussie Dist. M.K. in Adelaide (also agents for U-Beaut,I think)who were not interested in importing one for me. Particular thanks to Johnno who is a mine of info in general and put me on to this firm in particular.
What with the rate of exchange,import duty, shipping & G.S.bloodyT.its going to cost about $700 all up and should arrive in the next week or so. Thanks again to all.
Regards John H. http://ubb.ubeaut.com.au/ubb/biggrin.gif

John Saxton
1st September 2000, 07:31 PM
John,good to see you having a win mate,though our esteemed Pollies could have done something about the dollar by now and gotten you a better rate before you bought http://ubb.ubeaut.com.au/ubb/mad.gif
Cheers http://ubb.ubeaut.com.au/ubb/smile.gif

------------------
Johnno

JackoH
2nd September 2000, 05:18 PM
Johnno. 38.9 pence to the $. 5% import duty.$67.50 delivery.+10% G.S b*^#!|yT.on the lot!!! http://ubb.ubeaut.com.au/ubb/frown.gif
Regards John H.

STEPHEN MILLER
26th September 2000, 09:50 PM
John if you want a router lathe try Timbecon in W.A. they have a Sherwood listed as available mid 2000 web address is www.timbecon.com.au (http://www.timbecon.com.au) . They do mail orderprices are around $220 plus GST. plus frieght. regards steve

JackoH
27th September 2000, 02:25 PM
Thanks Steve. As I said in my post of Sept 1st. I have ordered and now received the Trend Router Lathe. It seems to be a good machine and I think I will be able to do all I want with it. All I have to do now is save up to pay Visa-card for all those Oz dollars that the conversion from pounds sterling gobbled up!
Regards and thanks again.
John H. http://ubb.ubeaut.com.au/ubb/frown.gif

Cosky
28th September 2008, 01:20 PM
HI all
dont know if this thread is still going,
Ive owned and have used this Router Lathe and still use it, its an amazing tool, i brought it in 1990 from Izaac Lords in High Wycombe Bucks Were i was born, and lived for 35 years. did my time at Gomm Brothers Gordon Road HW.
been woodwoking for over 30 years now. Now i live in Perth West Australia since 1998.
The lathe is an all round wood or Aluminium turning tool.
ive done some amazing stuff with this lathe, i brought it for 118.00 UK pounds in 1990 when i ran my own company, Pauls Furniture High Wycombe.
i have all the original tools and cutters ans frame, its setup on a 25mm mdf block.
have a look on my web site to see more. Barley Twist Columns are my faverite turning,
also i mad a set of forward controls from billit aluminium, and turned them on this router lathe,:2tsup:
http://www.members.tripod.com/coskys0/id27.htm

imdusty
29th September 2008, 11:41 PM
http://www.houseoftools.com/product.htm?pid=169889

JackoH
30th September 2008, 09:16 AM
That was 8 years ago! I no longer have that piece of c^*p!!

damienhazo
2nd October 2008, 11:46 PM
Please post some pics when it comes. A couple of years back, my Trend rep here said they were discontinuing the lathe but an improved version might be hitting the market. Would be very interested to see what you've ordered...

There was a link in here a while back to an American manufacturer and the thing looked bloody fantastic. A well-machined geared system a lot better than the little thing from Trend which uses cables... (the old one anyway)

Damien

Cosky
3rd October 2008, 01:26 AM
I have a full and complete manual and the original templetes for all the styles of turning


Router Lathe manual Link:
http://www.mediafire.com/?nfmvijmkzn1

Cosky
4th October 2008, 04:17 AM
Router Lathe manual Link:
http://www.mediafire.com/?nfmvijmkzn1

Chair Legs1 Link:
http://www.mediafire.com/?mtrjjbdn2jn

Chair Legs2 Link:
http://www.mediafire.com/?jckzzv1yxzz

RETIRED
14th October 2008, 07:20 AM
Please post some pics when it comes. A couple of years back, my Trend rep here said they were discontinuing the lathe but an improved version might be hitting the market. Would be very interested to see what you've ordered...

There was a link in here a while back to an American manufacturer and the thing looked bloody fantastic. A well-machined geared system a lot better than the little thing from Trend which uses cables... (the old one anyway)

Damienhttp://www.legacywoodworking.com/ Is this the one Damian?