View Full Version : Ripples inside lidded box
lubbing5cherubs
27th December 2006, 01:19 PM
Gidday I am back with another question. I am stil getting ridges inside my boxes. What the secret to getting rid of those please?
Toni
SawDustSniffer
27th December 2006, 01:43 PM
i think the ridges inside my deep bowls are from the chisel flexing while cutting , tryed to take smaller passes ,but that takes to long , so my next one i might make a thicker chisel , ( having a mate with a mill makes it easy ) looking around for some 25mm HSS dowel :~ might have to bye a length:~
i also tryed not sticking the chisel in straight , but paring toward the middle of the bowl bit by bit as you go deeper ,that seamed to help ,but still ended up rough as guts , im a newbie at turning so take this as gossball
DJ’s Timber
27th December 2006, 01:50 PM
Light cuts is normally the go, I use a scraper and try to knock the tops off the ridges, then take one complete pass
lubbing5cherubs
27th December 2006, 01:52 PM
how do you use a scraper when it larger the the radius of your box though?
toni
DJ’s Timber
27th December 2006, 02:00 PM
I take it your talking about where the bottom meets the side.
I have a few scrapers with different ground shapes on them, you might need to regrind one of your scrapers or buy another one :sneek: if you can get pass hubby :~ .
I normally use one just for the bottom and one for doing the the small radius and the sides
Skew ChiDAMN!!
27th December 2006, 04:55 PM
Another trick is to use a BIG old screwdriver that has seen better days. Cut the end off, then grind one side flat for about an inch. Thinking of that flat as the "top" of a scraper, sharpen the end with a nicely rounded profile.
I'm pretty sure I've posted pix of it before... [rummage, rummage] Yep... here's the Side (http://www.woodworkforums.com/attachment.php?attachmentid=26478&d=1152948925) & Top (http://www.woodworkforums.com/attachment.php?attachmentid=26477&d=1152948925) views of the cutting edge.
This is my "fits all round corners tool." :) If the curve of the scraper is too big to fit in the corner, I just roll it on it's side until it fits. Because it's just a screwdriver it's not the best steel in the world and needs fairly regular sharpening. But it's just soooo bloody convenient that it's worth the hassle. ;)
Wayne Blanch
27th December 2006, 06:17 PM
Another trick is to use a BIG old screwdriver that has seen better days.
What a great idea Skew. I'll haff to git me one o' dem! :) Sorry too much time with the kid over the past few days.
Toni, I tend to agree with djstimber I normally get the item close take any lumps off with a scraper and then one or two really light cuts to get that nice smooooth finish. Works for me anyway:cool:
See ya
Wayne
hughie
27th December 2006, 10:31 PM
[Gidday I am back with another question. I am stil getting ridges inside my boxes. What the secret to getting rid of those please?
Hi Toni,
Smaller cuts and smoother cuts ie take it a bit slower. Then use the scraper to finalize the shape and smooth the whole deal out. But scrape at 45' or so [shear scraping] to the wood. Not with the scraper flat on the tool rest.
http://www.maine-web.com/woodturning/shapeshifter/scaper.html
http://www.sydneywoodturners.com.au/site/articles/techniques/scraper.html
I have a couple of scrapers [home made] with varying radii. Ideally the scraper should be a bit smaller on the radius than the bowl being turned.