Picture(s) thanks: 0
Results 1 to 15 of 18
Thread: 15 inch Overhead beam
-
16th January 2024, 03:03 PM #1New Member
- Join Date
- Oct 2014
- Location
- Melton,Australia
- Posts
- 4
15 inch Overhead beam
Hi Guys, I have in a back room of my home, in it a 15inch overhead wooden beam, that currently has a ceiling fan attached to it. I wish to drill two holes one at either end of the beam to thread electrical wire through so I can attach two pendant lights to increase the lighting in that room. The holes would have to be drilled vertically from underneath, as there is insufficient space between the top of the beam (maybe 7 inches) and the ceiling itself. Can anyone tell me how to drill the holes perfectly straight from underneath, and what bits/auger I will need.
Cheers zippo01
-
16th January 2024 03:03 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th January 2024, 05:06 PM #2
First, make a drilling jig - just get a small piece of heay timber, say 100 x 50 x 300 mm - and dril a hole in the middle with a drill press. his ensures it is vertical.
Second, clamp the jig in position underneath the ceiling beam.
Third, drill the hole using the jig as your aligning tool,
Fourth. The drill bit must be of the needed diameter and at least 15 inches cutting length. Personally, I would prefer a spurred auger bit like this as they drill cleanly and accurately.
Spurred Auger Bit.jpg
I would avoid standard twist drill bits or spade bits as, in my hands, they do not drill accurately over those distances.
-
16th January 2024, 08:51 PM #3GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 1,166
How thick is the beam? Make sure you're not taking out too much meat of the beam?
I'd suggest similar to the method above, but starting with a smaller length bit. So pretty much a standard drill bit and an nice accurate guide to start off.
Then look at a guide/jig for your long boy 400mm bit.
At least with the hole started theres less chance of it wandering off
-
16th January 2024, 09:16 PM #4GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,669
Running the wire down the outside of the beam isn’t an option?
-
17th January 2024, 10:39 AM #5New Member
- Join Date
- Oct 2014
- Location
- Melton,Australia
- Posts
- 4
15inch overhead beam
Hi,
In reply the beam is 8cm/ 3 1/4 inches thick.
-
17th January 2024, 10:42 AM #6New Member
- Join Date
- Oct 2014
- Location
- Melton,Australia
- Posts
- 4
15 inch overhead beam
Hi,
In reply, no I don't want to run the wires down the side of the beam as its a feature stained beam that runs the length of the room. I want to hide the wires. Beam is 38 cm in height and 8 cm thick.
-
17th January 2024, 11:00 AM #7
-
17th January 2024, 11:20 AM #8
-
17th January 2024, 11:47 AM #9
I would use the drilling jig Graeme mentioned but start the hole with a shorter standard drill bit to get a 2 to 3 inch start on the hole. Then your longer auger will be set to mostly go through OK.
With augers and the small screw at its tip . I have filed these a bit dull sometimes to slow the aggressive pull they have into the wood. The more you dull them the more you have to push though. That's better than losing control though.
Rob
-
17th January 2024, 05:49 PM #10
-
18th January 2024, 01:44 PM #11GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,565
Perfectly straight or perfectly plumb and why is either important just to feed wires?
-
18th January 2024, 09:20 PM #12GOLD MEMBER
- Join Date
- Apr 2019
- Location
- NSW
- Age
- 38
- Posts
- 1,166
I would assume its an exposed beam... and it might like a bit silly if 3/4 up the side of the beam a random hole and wire juts out that then has to be fed into the roof
like the fan in this picture, but without a wire on either side
ceiling-fan-hung-on-beam-should-we-drill-a-hole-through-v0-yo6h78jigs0b1.jpg
-
18th January 2024, 10:24 PM #13GOLD MEMBER
- Join Date
- Nov 2007
- Location
- melbourne australia
- Posts
- 2,669
It would need to be an extraordinarily inaccurately drilled hole to pop out the side ¾ of the way up!
-
19th January 2024, 08:27 AM #14
I think Forum members have pretty much nailed it. While the beam is sufficiently thick to allow for error in drilling, a guide to start (post #2)and a shorter drill initially (post #8) are going to make life easier. This is because you are drilling upwards. While auscabs comment on this type of drill with the threaded tip is correct and does tend to pull itself rapidly through timber if using a corded tool, I would not worry about filing the thread off. Just use a cordless drill, possibly on the slower speed to begin with, as this will be easily controllable. As you are drilling up any assistance from the screw tip will be welcomed. A drill bit of 12mm or 10mm would be ample for lighting wire.
Using a guide and a short drill first will mean not having to concentrate so hard on the task and you can just drill.
Regards
PaulBushmiller;
"Power tends to corrupt. Absolute power corrupts, absolutely!"
-
20th January 2024, 01:31 PM #15GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,565
Dangle a plumb bob down the side of the beam as a reference to help keep the drill vertical. It's a good idea to have a second person as a "navigator" as you need to observe the string from two directions to be plumb.
Just a thought - Check that the beam is actually hanging plumb before you start drilling. If not, a batten clamped to the side of the beam would give the correct angle.
Similar Threads
-
8 inch wheels and buffs on 6 inch grinder
By qwertyu in forum SHARPENINGReplies: 1Last Post: 1st October 2021, 11:29 AM