Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Attach glass to wood
-
30th August 2019, 02:44 PM #1SENIOR MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Posts
- 650
Attach glass to wood
Am I over rthinking it as usual?
Still going with the bathroom reno (geting there) and up to building the shaving cabinet.
Now the query. Want to attach/glue 4mm mirror to the doors. The plan is they will be 15mm bamboo ply like the rest of the piece. Now everything tells me that I need to do to both sides what I do to one, as with veneering????
2 doors about 350w x 700h.
Some options, some more complicated than others.
1 - use another substrate to attach mirror to and veneer back.
2 - the bamboo ply is a 3 ply material. I could remove the outer veneer and replace with mirror.
3 - just stick it on and hope for best.
Also any recommendations for adhesive?
Thanks for any help.
I will post some pictures of the vanity and cabinet soon.
-
30th August 2019 02:44 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th August 2019, 03:46 PM #2Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
If you really want to be safe, a piece of moisture resistant MDF or chipboard is probably best to stick the mirror to. The bamboo might be perfectly fine though, I've never used it.
You can get special mirror silicone to attach it, but any neutral cure silicone will do. A bead about 30-40mm in from the edge all around and a squiggle down the middle will be plenty, press it down firmly by hand and let it sit flat to cure for a day or at least overnight.
-
30th August 2019, 05:36 PM #3GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,551
As Elan has said, natural cure silicone is the go. I form "calamari" rings of silicone on the back of the mirror. This gives the benefit of suction when the mirror is pressed into position.
-
31st August 2019, 01:54 PM #4SENIOR MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Posts
- 650
I also thought of doing a series of vertical lines for the silicone and open at the bottom in case any moisture got in there it would just run down?
rustynail, does that mean you have done something similar to this?
-
31st August 2019, 07:54 PM #5GOLD MEMBER
- Join Date
- Aug 2011
- Location
- bilpin
- Posts
- 3,551
I prefer the rings as the suction created when the glass is pressed into position helps hold while the silicone is curing. This method allows venting behind the mirror and any moisture can run down and out. Inside the rings becomes a sealed vacuum. I use this method for mirrors and splash backs.
-
31st August 2019, 10:57 PM #6GOLD MEMBER
- Join Date
- Apr 2018
- Location
- Nsw
- Age
- 64
- Posts
- 1,357
Glaziers use the silicone like mentioned and double sided tape to hold it in place, supported by timber blocks until the silicone goes off
I think the other advantage of the double sided tape is it works like a spacer to keep an air gap behind the glass
-
31st August 2019, 11:49 PM #7SENIOR MEMBER
- Join Date
- Oct 2015
- Location
- Ringwood, VIC
- Posts
- 575
I think the original question though is should both sides of the panel be treated the same, to prevent warping?
If it was me, I'd be sealing both sides as you will the rest of the piece, before applying the mirror, using neutral cure silicon as suggested. Maybe scratch up where the silicon will be.
Russ
-
1st September 2019, 01:31 AM #8
Had you thought of using brackets like these ?
H0056_1-600x600.png
Rick
-
1st September 2019, 01:26 PM #9Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
I don't think scratching the surface is a good move, it'll just create more potential entry points for water/steam. The silicon will stick just fine on a polished surface.
Interesting side note and possibly too late... Everything I've read about bamboo flooring says that it's not suitable for wet areas and should not be used in bathrooms. I'm assuming bamboo board is essentially the same stuff, so...
Similar Threads
-
Transperent 'plastic like' way to attach discs of wood
By ueran in forum WOODWORK - GENERALReplies: 9Last Post: 3rd August 2015, 01:38 PM -
Any Ideas On How To Attach Glass Ball To Top Of Walking Cane
By stixman in forum WOODCARVING AND SCULPTUREReplies: 16Last Post: 16th January 2014, 05:22 PM -
Joining glass to wood
By laxation in forum WOODWORK - GENERALReplies: 12Last Post: 14th May 2011, 06:17 PM -
Joining wood to glass
By Janny00 in forum WOODWORK - GENERALReplies: 13Last Post: 13th January 2009, 12:34 PM -
Glass on wood tabletop
By chicagollee in forum WOODWORK - GENERALReplies: 1Last Post: 11th January 2008, 05:03 PM