Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Bandsaw tracks to the left WHY ?
-
29th October 2018, 10:40 PM #1Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
Bandsaw tracks to the left WHY ?
I recently purchased a new Hafco Woodmaster bandsaw it continually tracks to the left. I have centred the guides, centred the blade on the wheel and tensioned the blade as per manual. But it still tracks to the left. Should I release some of the tension or what ?. Any suggestions most welcomed.
-
29th October 2018 10:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
29th October 2018, 10:42 PM #2Novice
- Join Date
- Aug 2017
- Posts
- 15
Maybe the first cut you made took the edge off blade
Sent from my iPhone using Tapatalk
-
29th October 2018, 10:58 PM #3SENIOR MEMBER
- Join Date
- Jul 2014
- Location
- Brisbane
- Posts
- 937
This video on setting up bandsaws is brilliant https://youtu.be/wGbZqWac0jU One point is the gullets should be centered on the wheels, not the body of the blade.
If it still tracks left, the set on your blade teeth may not be the same either side.
-
29th October 2018, 11:06 PM #4
Do you mean that when cutting the blade is being pulled left into the wood?
If so then you have blade drift and that is caused mainly by two things, either the blade is heavily set or blunt on one side in which case you need to replace it, or the fence isn’t aligned to the direction of cut of the blade.
If it’s the fence you can test this by removing it completely and clamping a battern or similar to the table and angling it so your timber is fed into the blade from a diferent angle, after a bit of trial and error you should be able to get it cutting straight. Once you’ve identified the angle, then you need to undo all the table securing bolts and physically rotate it so that the fence aligns to the angle you’ve worked out.
Let us know how you get on!Nothing succeeds like a budgie without a beak.
-
29th October 2018, 11:38 PM #5SENIOR MEMBER
- Join Date
- Dec 2012
- Location
- Australia
- Posts
- 684
If its the stock blade that came with it, try a new blade. I found the stock blade that came with my jet bandsaw to be terrible. Got some replacement blades and helped a lot. The sharper the blade, the more forgiving your tracking will be to start. Typically a blade positioned too far back on the wheel will cut to the left. Ensure after every blade adjustment you're re-positioning your thrust bearing. Thrust bearing being as close as possible without touching is the rule I go by.
-
29th October 2018, 11:47 PM #6SENIOR MEMBER
- Join Date
- Jul 2004
- Location
- Adelaide
- Age
- 76
- Posts
- 768
Blades are a fairly cheap item, try another one and your problem may be solved.
Regards
Keith
-
29th October 2018, 11:59 PM #7
I agree that the issue is likely to be the blade having uneven set and sharpness. However I would suggest that you replace it with one made up by an industrial saw doctor rather than buying one or more over the counter ones from Hafco, Bunnings or the like. They tend to buy consumables like bandsaw blade from the cheapest sources and then sell at prices close to thta of the saw docs who make blades to customer requirements using quality US or European stock. When I lived in Melb I used to get my blades from Specialty Saws in Croydon, still have all my gear in storage so haven't bought any for a while but they were still in Coolstore Rd last time I was down there about a month ago. Run as a father and son business, father has been a saw doctor for probably 40+ years, junior probably for 15 or more.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
30th October 2018, 12:49 AM #8
Hi John
If the blade is typical, it will have too many teeth. If so, it will load with sawdust, and this will push the blade off track. This is exacerbated if you experience the blade struggling, and push harder. Out of interest, how many teeth per inch (tpi) and what is the width?
Regards from Perth
DerekVisit www.inthewoodshop.com for tutorials on constructing handtools, handtool reviews, and my trials and tribulations with furniture builds.
-
30th October 2018, 07:07 AM #9GOLD MEMBER
- Join Date
- Oct 2002
- Location
- NSW
- Posts
- 1,610
+1 on centering the gullets, not the centre of the blade, on the wheel.
Also, if the blade is too far *forward* on the wheel, it may tend to track left. Attached diagram was posted on SawmillCreek
Screenshot_2018-10-30-06-53-26.png
-
30th October 2018, 08:55 PM #10Novice
- Join Date
- Jan 2011
- Location
- Bright
- Posts
- 17
I appreciate all you woodies comment to my problem, thank you. I will try each one over the weekend and hopefully solve my problem.
Similar Threads
-
Workbench Tracks
By Islander in forum THE WORK BENCHReplies: 10Last Post: 5th July 2016, 07:25 PM -
What causes bandsaw blade to wobble left to right?
By sam63 in forum BANDSAWSReplies: 26Last Post: 18th April 2010, 01:03 PM -
?? Tank tracks ??
By TTIT in forum TOY MAKINGReplies: 35Last Post: 23rd January 2009, 01:01 PM -
Left Handed Bandsaw
By ravlord13 in forum BANDSAWSReplies: 3Last Post: 17th May 2008, 12:12 AM -
aluminium tracks?
By mic-d in forum DESIGNS & PLANS FOR PROJECTSReplies: 8Last Post: 19th September 2004, 12:36 AM