Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 20 of 20
-
23rd February 2014, 12:16 PM #16GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
Using them for inlays
Im using them for fine inlays. Example below. Upstrokes are mostly about 1mm wide (0.8mm for the one on extreme right).
cheers
Arron
tgw.jpgApologies for unnoticed autocomplete errors.
-
23rd February 2014 12:16 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th February 2014, 08:30 AM #17GOLD MEMBER
- Join Date
- Apr 2012
- Location
- Sydney
- Posts
- 1,503
Of course, there are good examples over in the Chisels-handmade subforum.
https://www.woodworkforums.com/f279/mini-chisel-138659
-
24th February 2014, 09:21 AM #18GOLD MEMBER
- Join Date
- Apr 2011
- Location
- McBride BC Canada
- Posts
- 3,543
I think that you are looking for wood carving tools.
1 or 2 mm is big and fat for the carvers who do the details with a magnifier.
Pfeil, Stubai, Auriou, Henry Taylor, Ashley Iles are the top flight.
Lots of others, right down to $12 for 12 edges, none of which can be either made or sustained as 'carving sharp.'
Described as in the old London Pattern Book, you're after a 1/1 or a 1/2.
The first number is the shape, the 'sweep' and the second number is the width in mm.
My smallest is a D9/2 and the biggest is a Stubai carving adze, 7/75.
Pfeil D-Series have shorter shanks and slightly smaller handles.
There are a bunch of very good bladesmiths who make "palm tools."
No, they aren't steel engraving tools, but those would work well, too.
If you plan to use the tool a lot, you get what you pay for.
No matter who the bladesmith was, carving sharp lasts about 30 minutes and the
edge management is entirely up to you with 30,000 grit.
-
24th February 2014, 11:00 AM #19Intermediate Member
- Join Date
- Jan 2012
- Location
- Sydney
- Posts
- 35
Have you tried...
Have you tried contacting a local blacksmith? there should be some on the central coast... alternatively you could contact the TAFE blacksmiths... I have completed all the blacksmithing subjects at Ultimo TAFE and the teachers there are really knowledgeable and I am sure could smash you out a thin chisel with the correct heat treatment! for some nominal fee... or they could recommend a blacksmith to you.
Unfortunately, I am not set up yet to do heat treatments at home...
it is coming though!
-
24th February 2014, 08:51 PM #20GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
So on Sunday I dropped three old saw files into the oven at 220 degrees for an hour. Then I ground them down to 0.6, 1 and 1.4 mm. Not real pretty as my grinding skills are rubbish but they do the job. How robust the edges will be I'll know in time.
Thanks for the advice
Cheers
ArronApologies for unnoticed autocomplete errors.
Similar Threads
-
How to cut narrow slot in timber?
By Dengue in forum WOODWORK - GENERALReplies: 18Last Post: 20th February 2014, 12:00 PM -
Thicknessing narrow edge
By GarethR in forum JOINTERS, MOULDERS, THICKNESSERS, ETCReplies: 3Last Post: 6th December 2013, 10:13 AM -
Narrow Oak Table
By Muchacho in forum WOODWORK PICSReplies: 6Last Post: 8th September 2013, 10:10 AM -
Narrow Lands on Chisels
By pmcgee in forum HAND TOOLS - UNPOWEREDReplies: 0Last Post: 7th November 2012, 11:07 AM -
Narrow beads with skew
By Tiger in forum WOODTURNING - GENERALReplies: 19Last Post: 8th September 2010, 01:08 AM