Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 32
-
5th December 2007, 10:51 AM #1
changing super tight ts blade!!!!!
hi all
does people have a good way of changing a super tight ts blade?
I tried to undo the spanner but the spanner that came with the ts is all bent, so i got a new spanner... but all i am doing is bending the metal stick. The bolt is nearly worn out i also used chain lubrication but no effect. i also tried hitting the spanner with a hammer but it just wares the bolt.
what do i do in this situation? should i keep trying or cut the bolt and get a new one?H.S.
-
5th December 2007 10:51 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
5th December 2007, 10:56 AM #2
I'll Bite
OK,
I'll Bite,
What is a TS
[A Lot of things]
I know I'll regret this.Navvi
-
5th December 2007, 10:59 AM #3
Table Saw???
-
5th December 2007, 11:03 AM #4Senior Member
- Join Date
- Aug 2007
- Location
- Wynnum Qld
- Age
- 76
- Posts
- 113
Is it a Left Hand Thread????
Cheers
Baz
-
5th December 2007, 11:12 AM #5Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Ts Problem.
Trade it in on a new one.
-
5th December 2007, 11:15 AM #6
yea a table saw, with Left Hand Thread
H.S.
-
5th December 2007, 11:17 AM #7
i tried again just then... so frustrated!!! really want to drill through the bolt!!!
H.S.
-
5th December 2007, 11:26 AM #8
I know this is suggesting a Code violation, but have you looked in the instruction manual - I think this is getting to the stage where you are allowed to look in it (when all else fails....) - there may be a trick mentioned in it.
Also, it might help if you let us know the Make and Model of the TS.Cheers
Jeremy
If it were done when 'tis done, then 'twere well it were done quickly
-
5th December 2007, 11:49 AM #9
which way are you trying to turn the nut?
I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
5th December 2007, 11:50 AM #10
I think from memory you have the 2325 TS right?
I am not familiar with that one specifically, but on mine, TS10L, as I stand in front of the saw, the nut is on the right hand side of the blade and to undo the nut you pull the spanner towards you.
My spanner that came with the saw is only relatively thin (4-5mm?) and I have never looked like bending it, or indeed have had to use force.
Be careful with hitting it with a hammer as you could easily bend the arbor and then you are really in trouble.
Brute force doesn't always win out..............(except if you are a boilermaker perhaps?)
-
5th December 2007, 01:10 PM #11
my model is mj2325B, yes i have checked the instruction manual. it says to insert lock bar into hole in the saw table and turn saw blade by hand until lock bar engages in saw spindle hole, loosen saw blade spindle arbor nut spanner (L.H. THREAD)
My lock bar, which is like 7mm thick is also bent.
looks like i have to cut the nut and buy a new oneH.S.
-
5th December 2007, 01:19 PM #12
I am not familiar with the saw you have but the rule of thumb is that the nut will slacken in the direction the blade spins. A good fitting spanner is required so if the nut is still not too badly mangled you are still in with a chance. If the nut is too far gone then try multi grips or a stilson spanner. You will then need a replacement nut. Or rather than do more damage to the nut get help from someone familiar with machinery like a mechanic.
Good luck with it
John
-
5th December 2007, 01:25 PM #13
So you've been trying to turn the nut clockwise? A left hand thread nut in the right size may not be as easy to get as you think, I would not be cutting it...
I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
5th December 2007, 01:47 PM #14
I've had a similar problem with a panel saw, in a joinery I was working. We had a mechaninc come out & he got the nut off by tapping (not too hard) on the end of the arbour while someone else held the spanner, I remember we had a length of pipe to give more leverage.
I also remember using heat to loosen tight nuts, as the nut will expand before the shaft.
Hope this helps"If you want to build a ship, don't drum up people to collect wood and don't assign them tasks and work, but rather teach them to long for the endless immensity of the sea"Antoine de Saint-Exupery
-
5th December 2007, 02:02 PM #15SENIOR MEMBER
- Join Date
- Sep 2007
- Location
- Nicholls ACT
- Posts
- 728
If you are turning it the right way then you are certainly doing it up too tight. The thread is left handed so the spinning of the saw keeps the nut on. Thile finger tight is too loose, but you only need to snug it up with the spanner. It will not come off with the saw running.
Similar Threads
-
How to Use a Japanese Plane 1: How to Set the Blade
By soatoz in forum JAPANESE HAND TOOLSReplies: 28Last Post: 9th April 2013, 07:50 PM -
Hafco BP-16A Upper guide twist
By Designsync in forum BANDSAWSReplies: 96Last Post: 25th June 2007, 03:57 PM -
ML-392 blade setting technique
By Redback in forum WOODWORK - GENERALReplies: 15Last Post: 8th October 2006, 08:05 PM -
Grinding (shaping) a blade for a scrub plane
By derekcohen in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 3Last Post: 17th May 2005, 03:14 PM -
Blade Height Winder Review
By Noel Butcher in forum TRITON / GMCReplies: 6Last Post: 13th May 2000, 02:31 PM