Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
24th January 2010, 09:25 AM #1GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Connnecting 32mm and 38mm vacuum hoses
The dust outlet on my son's Makita SCMS is 38mm OD, and I want to connect that to the 32mm ID hose of my shop vac.
Has anyone come across a neat way of doing that? I would welcome all suggestions and comments, pleaseregards,
Dengy
-
24th January 2010 09:25 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
24th January 2010, 11:03 AM #2
There are propper expensive joiners at some retailers, but I know you like the cheap approach like me, so would recommend just Gaffa tape. The grey plastic stretch stuff, works a treat . To avoid the abrupt change you can cut a plastic ice-cream container or similar to form a cone between the two first, then cover in Gaffa tape.
Neil____________________________________________Every day presents an opportunity to learn something new
-
24th January 2010, 12:03 PM #3
How about starting off with a couple of straight connectors, one of each size (if you have spare ones), if not, see if any of the plastic plumbing pipe or fittings will fit - or be made to fit by cutting them axially.
You could cut one or two short sleeves of the same plumbing pipe and then cut them axially too, so they will compress and fill the gap between the 32mm pipe and the 38mm pipe. I would overlap any joins in successive sleeves. Glue them all together and when dry, smear more glue around the internal steps to smooth the transition between the two diameters..
I know you believe you understand what you think I wrote, but I'm not sure you realize that what you just read is not what I meant.
Regards, Woodwould.
-
24th January 2010, 01:35 PM #4
Someone else suggested using a neoprene sleeve. The easiest source of neoprene is to get a stubby holder and cut and sew it to size. I haven't used this method yet but I like the sound of it as it gives some flexibility to the joint. This is useful with an SCMS or power tools like sanders etc. as they move. I am going through the same thing at the moment and have cobbled together irrigation pipe, electrical conduit and plumbing pipe.
Some of my pipe is 2-3 mm too big so I cut a sleeve about 50mm long then cut out 2 or 3 mm down the long side, making it a smaller diameter. PVC cement or gaffer tape seals it of.
I really wish there was some standardisation in small tool dust extraction, vacuum cleaners etc.
Let me know if you need help disposing of any cans of beer stuck in the stubby holders.
-
24th January 2010, 04:19 PM #5GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Back to basics
I spent some time at Bunnings today in their plumbing department, as you do, and came up with some bits and pieces that would do the job.
Rather than joining the 2 hoses, I found bits that would fit over the 38mm OD outlet on the Makita SCMS. It was then a matter of stepping down to the 32mm hose.
The end result is a fitting that goes on the Makita SCMS and connects to a 32mm hose. The large end of the fitting is 38mm ID, and the small end is 33mm OD, which fits a standard 32mm ID hose very snugly. This hose then goes to my Triton dust bucket.
The invoice is attached showing the part details, and photos showing the assembly, with the 32mm High Pressure pipe pipe cut to length. The HP pipe is at the big end, and the 20mm coupling is at the narrow end, with the stepped slab adapter in the middle.
The only short coming is that the ID of the small end is only 28mm - ie considerable flow reduction, but certainly better than the little dust bag on the SCMSregards,
Dengy
-
25th January 2010, 01:00 PM #6GOLD MEMBER
- Join Date
- Mar 2008
- Location
- Townsville, Nth Qld
- Posts
- 4,236
Durrrh! Too clever by half!
What a waste of time and money that was!
Went to the local vac shop this morning, and was shown how the standard 32mm hose fits snugly inside the standard 38mm hose, and with a bit of silastic, is an airtight join, almost invisible.
Still, it was a good learning experienceregards,
Dengy
-
25th January 2010, 08:32 PM #7GOLD MEMBER
- Join Date
- Jan 2006
- Location
- Bowral, NSW, Australia
- Age
- 74
- Posts
- 1,471
Similar Threads
-
Air hoses
By HD200Renegade in forum SAFETYReplies: 21Last Post: 3rd July 2007, 08:02 PM -
Type of air hoses
By Pulpo in forum HAND TOOLS - POWEREDReplies: 4Last Post: 28th June 2007, 01:22 PM -
Where to purchase 38mm pine? (Sydney)
By I_wanna_Shed in forum TIMBERReplies: 11Last Post: 11th March 2005, 07:07 AM