Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
27th December 2009, 10:08 PM #1Novice
- Join Date
- Dec 2009
- Location
- adelaide
- Posts
- 20
joining 2 laminate panels together
hello everyone
I have 2 pieces of rectangular laminate wood (both plates have the same thickness at about 15mm) and I want to put them together to make a bigger rectangle. It's going to be a door for a cabinet.
I went to bunnings and the guy there suggested a biscuit joiner. Though I can't justify the cost because I don't see using it again in the future.
so I thought of gluing 3 pieces of wood at the back of the plates to act as brace.I will be peeling of the laminate area where the piece of wood would make contact. I would be using a clamp to secure the glued pieces while it dries.
any thoughts to this idea?
thank you very much for the help
-
27th December 2009 10:08 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th December 2009, 10:13 PM #2
If you are in the northern suburbs I can help with the use of my biscuit joinerI have use a biscuit joiner on a few projects
regards Michaelenjoy life we are only here a short time not a long time
-
27th December 2009, 10:28 PM #3
Just butt join them with a decent adhesive, no bracing required.
-
27th December 2009, 10:51 PM #4Novice
- Join Date
- Dec 2009
- Location
- adelaide
- Posts
- 20
-
28th December 2009, 12:09 AM #5Novice
- Join Date
- Dec 2009
- Location
- adelaide
- Posts
- 20
Hello.
I searched the net for "butt joint" and I came across the wikipedia entry (Butt joint - Wikipedia, the free encyclopedia). And it seems there are several types (including biscuit joint).
Which one would you recommend (other than biscuit of course ? How do I make sure the 2 panels stay together while the glue dries? Also what brand of adhesive would you recommend?
Thank you very much for the help
-
28th December 2009, 05:02 AM #6Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
If you have the means to run a slot of known width across one end of each board you can then join with a suitable piece of ply. Like a long rectangular biscuit.
-
28th December 2009, 10:40 AM #7Novice
- Join Date
- Dec 2009
- Location
- adelaide
- Posts
- 20
-
28th December 2009, 12:01 PM #8
Prep both edges so they are square (use a plane or router), apply glue, press edges together, clamp lightly (no-one who works with wood can ever have enough clamps), remove glue squeeze out as required. No further support for the join is required, modern adhesives will generally make a join stronger than the timber.
More info with pics....
http://www.woodworking.org/WC/GArchi...ithglupan.html
http://www.lowes.com/lowes/lkn?actio...GluePanel.html
If the two panels are a (real) timber core, just use PVA glue (Aquahere or similar); if they are chipboard or MDF my first reaction would be to throw them away and simply buy a larger piece.
Chipboard is not all that good when joined edge to edge (no real strength in the material), so a few dowels could be used to give it a bit more - you can pick up dowels/drill bit/dowel locating tool from Bunnies for about $20.
-
28th December 2009, 12:29 PM #9Novice
- Join Date
- Dec 2009
- Location
- adelaide
- Posts
- 20
thank you
Similar Threads
-
Joining top and back plates
By zenobia in forum MUSICAL INSTRUMENTSReplies: 11Last Post: 29th May 2007, 01:11 PM -
plates
By weisyboy in forum WOODTURNING - GENERALReplies: 6Last Post: 12th September 2006, 07:46 PM -
Stuck together joining plates.
By Bodgy in forum BANDSAWSReplies: 5Last Post: 24th February 2006, 02:58 PM