Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: Drill press chuck problem
-
8th November 2003, 12:28 PM #1Member
- Join Date
- Oct 2003
- Location
- Perth, Western Australia
- Age
- 93
- Posts
- 76
Drill press chuck problem
Now and again the chuck in my drill press drops out.
Most of the time I am able to put it back with a sharp shove and it stays there, or I give it a little tap with a lump of wood.
Now if I were a machinist I would probably know all about morse tapers and how to humour them but I am not and I dont. So can anyone give me the lowdown on care and maintenance?
Ray
-
8th November 2003 12:28 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
8th November 2003, 01:03 PM #2
You could try some soft chaulk on the taper and then tap it back in
Station-rat
-
8th November 2003, 03:23 PM #3
Thats the one! . . . providing there is no oil or grease on the taper.
If it has some lubricant of any sort, clean it with some turps, petrol thinner or the like, let it dry and apply chalk . . .dont forget to clean and dry the chuck's tapered hole too!
-
8th November 2003, 08:10 PM #4Member
- Join Date
- Oct 2003
- Location
- Perth, Western Australia
- Age
- 93
- Posts
- 76
Thanks guys.
That's chalk as in blackboard I presume.
Ray
-
8th November 2003, 08:58 PM #5
yep Ray or just pinch some of her indoors talcum powder
What this country needs are more unemployed politicians.
Edward Langley, Artist (1928-1995)
-
9th November 2003, 11:41 AM #6Member
- Join Date
- Oct 2003
- Location
- Perth, Western Australia
- Age
- 93
- Posts
- 76
Originally posted by fxst
yep Ray or just pinch some of her indoors talcum powder
Oh I get it. Would that be before or after application?
Ray
-
15th November 2003, 09:00 PM #7
superjaws
It takes a decent whack to get it in to stay.
I was using a 4x2 but I felt the spin was wobbling.
I then stacked hard wood and tried to press it in.
Then I had a flash and used the superjaws on it.
Haven't had a problem with it since.Last edited by barrysumpter; 16th November 2003 at 08:19 AM.
Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
16th November 2003, 06:47 PM #8Member
- Join Date
- Oct 2003
- Location
- Perth, Western Australia
- Age
- 93
- Posts
- 76
Barry,
Are we talking about the same thing?
-
16th November 2003, 07:48 PM #9
Check this out....
This is what I'm talkin about:
http://www.cvfsupplycompany.com/drch5drprchw.html
Although, I did use the chalk on my hands to make sure the 4x2 didn't slip out of my hands.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge
-
16th November 2003, 11:03 PM #10
Barry
If that arbor of the chuck keeps coming out there is something wrong with either the morse taper of the arbor or the morse taper of the drill press. Try a mates arbor in your press, if it stays in, you know the chuck arbor is at fault and u can return it to the supplier.
Cya
Joe
Have fun................keep turnin
-
17th November 2003, 12:16 PM #11
I agree that it is an unusual problem, and that there could be a fault, as for Barry's whack with hardwood or superjaws . . . hum no idea. . . .actualy why not a one kilo mallet?
I can imagine Barry holding up the superjaws over his head to press the chuck in place on the drill press . . . .imagine the shape of the pulley cover or the pulley after such treatement . . . .he he
-
17th November 2003, 12:35 PM #12
smarter than my tools. i hope.
Opened the cover
packed the top with hardwood
clamped with jaws and exerted pressure with foot
Just checked - every so slight wobble
just curious - has anyone else had a good look while the drill press is running ?
do you get a slight wobble as well ?
Oh right, the wobble I've been addressing is the wobble I get when the dp is running. This might have been misleading. appologies.Thanks,
Barry G. Sumpter
May Yesterdays Tears Quench the Thirst for Tomorrows Revenge