Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: those foam rubber ear plugs
-
27th June 2013, 09:14 PM #1GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
those foam rubber ear plugs
I've been experimenting with those little, yellow, cones shaped ear plugs. The ones made out of very soft foam rubber. I find they work their way out of my ear canals soon after I put them in. Is there something I'm missing - or do I just perhaps have the wrong shaped ear canals ?
any advice
cheers
ArronApologies for unnoticed autocomplete errors.
-
27th June 2013 09:14 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th June 2013, 09:33 PM #2
Are you rolling 'em between your fingers to squash 'em?
If you do that just before putting them in your ears, when they spring back to full size they wedge in and fit better.
SWK
-
27th June 2013, 09:57 PM #3
Not kidding, but I use them often, and if working with noisy gear, (brushcutter, chainsaw, commercial CNC router etc) wear them under a set of muffs for added protection. Normally don't have them com out after rolling and inserting, but never loose them with a set of muffs over them.
I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was.
-
27th June 2013, 11:43 PM #4GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,330
I roll them and squash them for about half way along their length. Sounds like I should try squashing them along their full length and inserting them deeper.
ArronoApologies for unnoticed autocomplete errors.
-
28th June 2013, 12:30 AM #5Those were the droids I was looking for.
https://autoblastgates.com.au
-
28th June 2013, 05:37 PM #6SENIOR MEMBER
- Join Date
- Dec 2011
- Location
- Buderim qld
- Posts
- 842
-
28th June 2013, 06:38 PM #7
The Plugs.
Hi All,
Yes, I had the same problem, until I went to have Hearing Aids fitted.
What the Lady showed me made sense.
You Roll & Squeeze the Plug & start to fit it in the Canal, but with your other hand you grab the top of that Ear & lift & then the Plug just Slips in.
Hope that Helps, but other than that go to a Hearing Test Place & I'm sure they wood show you.Regards,
issatree.
Have Lathe, Wood Travel.
-
29th June 2013, 03:24 PM #8Novice
- Join Date
- Nov 2012
- Location
- Townsville
- Posts
- 11
Beat me to it. This is how I was shown to pit them in. If they have been properly inerted you should only see the end of the plug (once they have expanded). When you remove them they should be twisted out to so that you don't create a vacuum pressure that can damage the ear. Once they have been removed you will know if you were wearing them correctly because there is a dent about 2/3rds along the plug.
Simo
-
29th June 2013, 03:54 PM #9GOLD MEMBER
- Join Date
- Aug 2012
- Location
- Imbil
- Posts
- 1,167
they also are great inserted the same way into air tool fittings we have a lot of trouble with mud wasps around here bad enough in the nail gun but in the spray gun damm.
Regards Rod.
-
29th June 2013, 08:49 PM #10
I find that after inserting that if I hold the plug in for about a minute while the foam expands it stays in.
I wore ear plugs daily for about two years, and now use them monthly when running a 12 cylinder diesel generator.
Similar Threads
-
Foam rubber
By DIY DAN in forum BOX MAKINGReplies: 4Last Post: 10th January 2013, 04:53 PM -
Trailer Plugs
By smidsy in forum TRAILERS & OTHER FABRICATED STUFFReplies: 6Last Post: 27th July 2011, 08:12 PM -
Sticking foam rubber
By Tools in forum UPHOLSTERYReplies: 5Last Post: 7th May 2010, 08:58 PM -
Shaping foam rubber
By AlexS in forum BOX MAKINGReplies: 14Last Post: 26th November 2008, 03:37 PM -
painting foam rubber
By mattgranger@net in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 0Last Post: 27th July 2006, 03:55 PM