Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 4 of 4
-
22nd May 2012, 06:39 PM #1Senior Member
- Join Date
- Jun 2011
- Location
- Bald Hills
- Posts
- 127
New Folding outfeed table and saw wing infill
Ive started on a full workshop makeover[IMG]file:///C:%5CUsers%5Cgreg%5CAppData%5CLocal%5CTemp%5Cmsohtmlclip1%5C01%5Cclip_image001.gif[/IMG]...first step was a new outfeed table for the table saw.The one i had before on the old saw was good but this time i wanted to make a few changes.
First thing was i didnt reckon i needed it the full width of the saw (i only cut a full sheet once in a blue moon)so 600mm wide ment that 95% of jobs would be suited. Also when i refit the shop it will give me room beside the table to use the drill press (at this stage thats where its going)
I wanted to have a full run through for my sled (start on that tomorrow) and for those times when i have something long , a fold up extension .That way only the area i really need is being used ,and with the extension down i have plenty of room behind for where the jointer and router table are going to be.
I welded up a sliding support for the extension and it seems to work well, there is a bit of sag...but that wont be a problem..the main part is dead level and sits almost 1mm below the tablesaw height so there wont be any catching as wood is feed through.
Made of 2 sheets of ply glued and screwed together the table is strong , hardwood trim will take of bumps and add to strength.
The laminex top makes for a nice slick surface.
I might add a small shelf . not quite sure yet....plan to make a pull out cabinet to fit under the right wing to hold push sticks and jigs..so a shelf might not be needed..but i hate wasting space.
-
22nd May 2012 06:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
22nd May 2012, 08:40 PM #2
Nice job, and nice saw
I made one similar recently but I haven't added the mitre slot extensions yet. I just fold it down if I need to use the sled. I have an adjustable, hinged leg and the whole table folds flat against the front of the saw.Those were the droids I was looking for.
https://autoblastgates.com.au
-
22nd May 2012, 08:57 PM #3
Good job on the extention.
Does look a little crowded so using as much of the space as possible good idea.
-
22nd May 2012, 09:02 PM #4Senior Member
- Join Date
- Jun 2011
- Location
- Bald Hills
- Posts
- 127
Ive got things all moved around at the moment in the way...have to try and do the refit by moving a to b to c back to a then to c....the dustcollector is going to go outside, until then its going to be a pain working around things esp when i pull out the cabinets to replace them...
Similar Threads
-
Setting up planer outfeed table on Hammer C3 31
By lachstar in forum TABLE SAWS & COMBINATIONSReplies: 5Last Post: 24th May 2012, 11:12 PM -
Tablesaw - Outfeed Table?
By icor1031 in forum WOODWORK - GENERALReplies: 4Last Post: 7th January 2012, 02:16 PM -
Finish for MDF Top - Outfeed / Assembly Table
By Arry in forum FINISHINGReplies: 8Last Post: 21st May 2011, 10:07 PM -
Queen Anne Bedroom dresser - folding wing mirror
By LenS in forum WOODWORK - GENERALReplies: 2Last Post: 17th November 2006, 06:51 AM -
Roller infeed/outfeed table
By Sturdee in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 9Last Post: 15th October 2003, 09:44 PM