Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: End grain or not?
-
4th August 2004, 02:49 PM #1
End grain or not?
Hi Folks,
I'm currently making a coffee table from recycled pallet timber. I would like to know what to do as to the ends of the table top? that is whether I leave the endgrain showing or not ?
The timber in question is a light colour, a couple of pieces are definately stringy bark the rest is questionable.
All sugestions will be welcome as I have absolutely no idea as to what to do.
Himzo.There's no such thing as too many Routers
-
4th August 2004 02:49 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
4th August 2004, 02:57 PM #2
depends if its a splitty/splinterywood if/and the end grain looks good dunnit ? I reckon end grain shaved nice and clean looks ace meself. especially if you run a fancy bead of some form with your router around the edge.
really its a personal preferance - ask you SWMBO - she'll tell ya what fits best with the curtains....Zed
-
4th August 2004, 03:13 PM #3
I like to round over the ends of end grains, fill them and then just treat them like the rest of the table. If the grain is dense enough them I wouldn't even bother to fill the grain, just finish it with whatever.
Last edited by Bob Willson; 5th August 2004 at 04:57 AM.
Bob Willson
The term 'grammar nazi' was invented to make people, who don't know their grammar, feel OK about being uneducated.
-
4th August 2004, 08:42 PM #4Originally Posted by Bob Willson
Whats this whatever finish you speak of? Is it something new? Is it in THE BOOK?
Whatever oh Whatever is a whatever finish? :eek:Boring signature time again!
-
4th August 2004, 09:41 PM #5Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Gees, Its next to the thingy behind the whatsit siitting at the back of the thingamajig down by the whoosy.
Donchanonothing?
-
5th August 2004, 01:37 AM #6
If it is without fault then nothing wrong with the honesty of endgrain.
If you are going to hide endgrain you might as well just use ply.
ross
-
5th August 2004, 04:56 AM #7Originally Posted by outbackBob Willson
The term 'grammar nazi' was invented to make people, who don't know their grammar, feel OK about being uneducated.
-
5th August 2004, 10:05 AM #8
Thanks folks,
I think I'll go with the rounded over, smoothed and finished with whatever . I tried it on a piece of off cut from the original and seemed to come up OK.
Whatever should be stored away from all the sparky thingo's as well .
thanks again, advice great as always.
Himzo.There's no such thing as too many Routers
-
5th August 2004, 11:24 AM #9
Himzol,
Just be careful because the endgrain will absorb more finish than along the grain which can make it look darker. If you fill the endgrain, the effect is not so noticeable. This especially applies when you are staining.
Check it out on a piece of scrap and fill with shellac.
- Wood Borer
-
5th August 2004, 06:59 PM #10
and if youre routing the top to get the rounded edge, do the end grain first ..... IMO: whether or not to show end grain depends on the desired level of finish and style of the table .... often, a slim breadboard end can look great.
Steve
Kilmore (Melbourne-ish)
Australia
....catchy phrase here
-
6th August 2004, 09:30 PM #11Originally Posted by
Gettit roight , It's Donchanonuffink.
DanIs there anything easier done than said?- Stacky. The bottom pub, Cobram.
-
6th August 2004, 09:39 PM #12SENIOR MEMBER
- Join Date
- Jun 2004
- Location
- Kyabram. Vic
- Posts
- 826
Hey Dan,
Sounds like you have had quite a few visits to the bronx end of town. LOL
You have their accent down pat.
Ken