Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 62
Thread: How was this achieved?
-
29th November 2006, 04:56 PM #1Member
- Join Date
- Nov 2006
- Location
- Melbourne
- Posts
- 64
How was this achieved?
Hi guys,
How was this build - I see no nails/bolts etc. how are they holding together??
:confused:
-
29th November 2006 04:56 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
29th November 2006, 05:10 PM #2
Have a look over in the back corner Leo, there's what appears to be a 2"x2" vertical which would probably be nailed/screwed within an inch of it's life....
-
29th November 2006, 05:35 PM #3
It is probably joined using sleeper nails. 10" long mean mothers. Then, the box is turned upside down so they cant be seen.
another method is to drill holes and use reinforcing rod to 'dowel' them together. The blocks in the corners nail into the sleepers to keep the corners tight. However, if you bend the reo bar a little there is no need even for that.
-
29th November 2006, 05:39 PM #4Member
- Join Date
- Nov 2006
- Location
- Melbourne
- Posts
- 64
-
29th November 2006, 05:49 PM #5
I'm fairly certain there are actually two units, one on top of the other, and the small square timber is to stop side slip. It has nothing to do with holding the unit together.
-
29th November 2006, 06:00 PM #6
Its a good spot for a sliding dovetail joint...
....................................................................
-
29th November 2006, 07:19 PM #7Member
- Join Date
- Feb 2006
- Location
- Hawkes Bay, New Zealand
- Posts
- 83
Dunno
if I'm seeing things, but aren't there slightly lighter-coloured dowels covering up some sort of fixing? (three at each end of each sleeper)
-
29th November 2006, 07:46 PM #8Banned
- Join Date
- Jun 2005
- Location
- Earth, occasionally
- Posts
- 886
Hi Leo,
I would agree with Groggy. Most likely there are large steel (or timber) dowels which have been placed in large augered holes in each block. I think you can actually buy specific products for this from Landscape Garden supplies.
Regards,
Rob
-
29th November 2006, 09:58 PM #9
Could it not be a blind mortice/tenon? Or a mitred biscuit joint with the tops cut square to hide it? Or as others have suggested, dowel joints? Lots of ways to do this surely?
-
29th November 2006, 10:06 PM #10
I'm with Christopha, its most likely just a solid cleat in each corner on the inside which is skew nailed or screwed.
I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
29th November 2006, 11:49 PM #11
You can bet your boots if it was done by a builder it won't be rocket science.
Keep an eye on it for the next year or two.... I recon she will be looking pretty second hand pretty quickly.
cheersAny thing with sharp teeth eats meat.
Most powertools have sharp teeth.
People are made of meat.
Abrasives can be just as dangerous as a blade.....and 10 times more painfull.
-
29th November 2006, 11:57 PM #12Member
- Join Date
- Nov 2006
- Location
- Melbourne
- Posts
- 64
-
30th November 2006, 12:10 AM #13
Magic methods of cabinetry seem somewhat excessive for a planter box. I'd bet on the cleats, maybe stouter on the lower set. Dig up some of the dirt and see what's there.
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
30th November 2006, 12:22 PM #14Member
- Join Date
- Nov 2006
- Location
- Melbourne
- Posts
- 64
The box is in US, i found a pic on the net.
http://www.railwaysleeper.com/Ian%20...%20project.htm
The description says:
'... Note the small supporting posts on the inside of the construction, that connect the different sleeper walls together, and yet is invisible when the bed is infilled with soil.'
That's all.
So, they must've used nails. :confused: The white spots on the outside of sleepers are not coverings for bolts, because the height of the post is lower than position of the white discoloration. I am just guessing here.
-
30th November 2006, 12:27 PM #15