Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Interstate Transport of tools
-
4th January 2006, 11:43 AM #1
Interstate Transport of tools
Okay I am planning on moving from Canberra back to Melbourne.
I have the following bench mounted tools and was wondering if there is anything I should need to know about transporting them before hand.
Obviously unbolt them from the bench!
Band Saw
Mitre Saw
Rip Saw
Router Table
Drill Press
Sander
Also can anyone recommend a good removalist?______________________________________________
Don't call me a nerd ! Nerds are ppl who have an obsession with awesome new gadgets. I am the person that nerds call when they have a problem with those gadgets!
I am a Geek!! Get it right!!
-
4th January 2006 11:43 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
4th January 2006, 12:04 PM #2
Unplug the power cords.....
Life should NOT be a journey to the grave with the intention of arriving safely in an attractive and well preserved body, but rather to skid in sideways - Chardonay in one hand - Strawberries in the other, body thoroughly used up, totally worn out and screaming - "WOO WOO...What a ride"
-
4th January 2006, 12:59 PM #3
You may want to bolt them to boards for the transporting phase. That way, they will have a flat base to sit in withn any boxes you make for them.
Don't forget, you need to drop off all that Huon Pine you found the other month at my place before you go. It will save the transporting costs!Burn
When all points of view have equal time The chatter of idiots will drown out the wise
-
4th January 2006, 01:00 PM #4Originally Posted by Andraax
Band Saw - remove blade, ease tension, tape knobs etc. Store fence seperately. Wipe top with a protective film.
Mitre Saw - Lock the head, I would also remove the blade. Tape all knobs.
Rip Saw - ? Hand held? Put heavy tape over the teeth. Fold cardboard over the edge then tape it on.
Router Table - remove router bits. Remove router. Make sure you inventory the router bits, they cost more than the router!
Drill Press - wipe down metal with protective film (NOT WD40) Camelia oil is great if you have it. Remove and bits. I would also remove the head, but that's just me. Lower table to lowest position.
Sander - Orbital? Blow dust out and put in a carton. Bench model, same, remove any belts.
-
4th January 2006, 01:08 PM #5Originally Posted by burn
Missing having and reasonable stock to work on though - which is probably good as I have to start packing some time.______________________________________________
Don't call me a nerd ! Nerds are ppl who have an obsession with awesome new gadgets. I am the person that nerds call when they have a problem with those gadgets!
I am a Geek!! Get it right!!
-
4th January 2006, 01:09 PM #6Originally Posted by Groggy______________________________________________
Don't call me a nerd ! Nerds are ppl who have an obsession with awesome new gadgets. I am the person that nerds call when they have a problem with those gadgets!
I am a Geek!! Get it right!!
-
4th January 2006, 01:10 PM #7Originally Posted by burn______________________________________________
Don't call me a nerd ! Nerds are ppl who have an obsession with awesome new gadgets. I am the person that nerds call when they have a problem with those gadgets!
I am a Geek!! Get it right!!
-
4th January 2006, 01:16 PM #8
G'day Aandrax,
When I towed up a trailer from Melbourne to get the rest of my machinery / tools from Brisbane I:
• bandsaw: totally seperated the bandsaw from its stand, took the blade off, and chocked the table of the bandsaw to the trailer so it didn't move.
• drill press: again totally seperated it piece by piece, especially as the column was solid steel.
Had a stack load of other stuff, but only wrote what is applicable in your circumstance.
-
4th January 2006, 01:36 PM #9
Andraax,
If your table saw is a cabinet saw it maybe advisable to either remove the motor or somehow support the weight of the motor on to the cabinet. From memory, the saw I have, when originally delivered, had a large block of polystyrene foam wedged under the motor and the saw tilted to about 45 degrees to press the motor down hard on to the foam. I've read accounts of trunnions being broken when roughly transporting cabinet saws.
I don't know much about contractor saws, but it woul also seem like a good idea to remove the rear-hanging motor before transporting.
I think Groggy's advice for all the other tools is sound.
Chris
-
4th January 2006, 01:55 PM #10Originally Posted by chrisp
Similar Threads
-
The traditional Tools Group Inc (TTTG)
By Heavansabove in forum HAND TOOLS - POWEREDReplies: 0Last Post: 14th December 2005, 10:55 AM -
The Best Reasons for Buying Tools
By derekcohen in forum WOODWORK - GENERALReplies: 28Last Post: 4th November 2005, 08:27 AM -
what wood carving tools to buy
By nadcarves in forum WOODCARVING AND SCULPTUREReplies: 0Last Post: 24th May 2003, 11:57 AM -
Quality of tools
By John Saxton in forum WOODWORK - GENERALReplies: 10Last Post: 25th April 2002, 01:55 PM -
Newbie; Are crown tools any good?
By OG in forum HAND TOOLS - UNPOWEREDReplies: 4Last Post: 7th March 2002, 02:52 PM