Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Laminated Pine Panels
-
14th January 2011, 10:02 PM #1Apprentice
- Join Date
- May 2009
- Location
- Melbourne Eastern Suburbs
- Age
- 54
- Posts
- 26
Laminated Pine Panels
Hi,
I have a stupid question to ask relating to laminated pine panels.......
Is there any danger that a laminated pine panel may start to 'breakdown' if it is subjected to multiple cuts??
ie, if I was to purchase a 1800 x 600 x 19 sheet and cut it into many & varied sizes, would the individual lengths start to pull apart?
-
14th January 2011 10:02 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
15th January 2011, 12:27 PM #2Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Shouldn't. The glued joints should be stronger than the timber.
-
15th January 2011, 08:37 PM #3GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
I agree with Artme The laminated pine panels are usually better as all the crap bits with knots etc are docked before the sections are joined into a large panel .
Regarding the "stupid" bit. As others have said on the Forums, it's not stupid to not know .I've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
15th January 2011, 09:53 PM #4
I've noticed when I look at the laminated panels stacked up in Bunnings that the top sheet almost always seems to be cupped.
I suspect they are very dry straight out of the factory and suck up humidity like a sponge. I haven't used one, but I'd think about taking extra precautions about acclimatising them before cutting/using.
-
17th January 2011, 07:53 AM #5Apprentice
- Join Date
- May 2009
- Location
- Melbourne Eastern Suburbs
- Age
- 54
- Posts
- 26
Thanks artme, peter36, fuzzie!
Noticed the same thing in the store myself ( top sheets being cupped )
Great point about acclimatising though!
Is there anything from a finishing & priming point of view that could help prevent this?
Would it even be beneficial to cut the panel into the segments ASAP after purchasing? Or quite the opposite?
-
17th January 2011, 08:34 AM #6GOLD MEMBER
- Join Date
- Sep 2004
- Location
- Melbourne
- Age
- 87
- Posts
- 1,327
Just don't buy the top sheet of course. Either keep both sides covered ( the top one with a cover sheet ) or keep both sides exposed to the air by sitting the panel on a couple of say 5cm high strips of timber .
After you have cut the panel do the same thing until you are ready put a finish/assembleI've just become an optimist . Iv'e made a 25 year plan -oopps I've had a few birthdays - better make that a 20 year plan
-
17th January 2011, 11:55 AM #7GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
Just to throw in $0.02 worth - when finishing do both sides not just the side you see. If one side is left raw, in humid weather you are inviting a problem.
Regards,
Bob
-
17th January 2011, 12:27 PM #8
What Bob said - only finishing/sealing one side of these pine panels is a good way to turn them into tubular pine....
Also check the panels carefully when buying - I saw these products at our local Bunnies, but noticed that several of them had open joints, i.e. delaminating, on the shelf .......
-
17th January 2011, 01:12 PM #9Apprentice
- Join Date
- May 2009
- Location
- Melbourne Eastern Suburbs
- Age
- 54
- Posts
- 26
Thanks everyone! Very welcome tips & information.
From a finishing & sealing point of view, I plan to finish both sides prior to assembly so hopefully this should limit the possibility of warping etc.
For the record, my plan is to make a small bed frame for my youngest.
I have scribbled up a plan to cut 2 of these panels into enough segments to make something simple but effective.
It is interesting to hear some of the responses to the panels found in some of the mainstream stores ( Bunnies ) After all, spotting these particular panels is what prompted me to the possible project idea.
Similar Threads
-
Advice re fingerjointed laminated pine
By Maddougs in forum TIMBERReplies: 10Last Post: 6th July 2008, 07:13 PM -
Laminated Radiata Pine Planks
By Barry_White in forum TIMBERReplies: 5Last Post: 11th December 2007, 07:17 AM -
laminated pine in melbourne
By old_picker in forum TIMBERReplies: 0Last Post: 30th November 2007, 04:55 PM -
Laminated H3 pine 70x90
By Timmypig in forum TIMBERReplies: 5Last Post: 25th October 2005, 10:45 PM -
Laminated Timber Veneer Panels
By Boat Guy in forum BOAT BUILDING / REPAIRINGReplies: 2Last Post: 25th August 2005, 11:51 PM