Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
-
28th June 2013, 11:21 AM #1New Member
- Join Date
- Jun 2013
- Location
- Perth
- Posts
- 2
melamine cabinet swelling - how to seal?
Gday lads,
i noticed the other day a corner on one of our bathroom cabinets has started to swell from moisture, these are melamine cabinets and while they dont get water on them directly its a small bathroom so very high humidity after a shower etc.
i want to seal it up before it gets any worse and was wondering what is best way to do that? my first thought was just wack some silicone over it...
-
28th June 2013 11:21 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
28th June 2013, 01:48 PM #2
Good Morning Towersofdub
Firstly, welcome to the Forum with your maiden post.
Sad state of affairs with your bathroom cabinets. The real damage was done when the material for the cabinets was ordered in that it is ST (Standard) rather than HMR (High Moisture Resistant) melamine - the latter can be easily reconised in that the chipboard has a greenish colouring. ST melamine really does not have a place in any bathroom, kitchen or laundry; moisture in the form of water vapour will always attack it.
Unfortunately, eventually you will almost certainly have to replace it.
You can probably delay the inevitable by sealing all edges of the melamine sheeting. This would involve totally dismantling the cabinet, then applying two or three coats of a suitable sealant to all, repeat all, the edges where the chipboard is exposed. Epoxy, polyurethane, danish oil, varnish or even paint would probably work. But, at best, this is only likely to be a temporary or delaying fix. Water vapour will enter the smallest pin hole in the sealant, even at the microscopic level.
Sorry to be such a bearer of ill-tidings on your first post.
Fair Winds
Graeme
-
28th June 2013, 02:49 PM #3New Member
- Join Date
- Jun 2013
- Location
- Perth
- Posts
- 2
thanks for the reply graeme, i had an inkling this was bad but not that bad.
to make things even better these are new renovations only a few weeks old...
-
28th June 2013, 03:27 PM #4
Sh*t happens.
I always use HMR melamine. It's usually the same price as ST, but for some unfathomable reason, many outlets, especially Big-Chain branches, do not stock it.
Was the "oversight" yours or someone elses. If a cabinet was bought as a bathroom cabinet and was later found to be made from non-HMR melamine (ie from water-absorbent chipboard) then it is arguable that the cabinet was not "fit for purpose". Probably not worth the hassles - write it off as one of life's little learning experiences....
Fair Winds
Graeme
-
28th June 2013, 03:38 PM #5.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,807
We have the same problem in out kitchen.
My plan is to seal it with two pack poly.
-
28th June 2013, 10:38 PM #6
Bob, please bite your tongue on my next comment.
Towersofdub, Bob is very knowledgable and very experienced, yet he is in a similar situation to you. We all benefit from hindsight.
Back to you, Bob. Are you sure that the two-pack poly will be compatible with the glues in the chipboard? Normally two-pack needs a virgin surface to be worry free. I would have guessed that one-pot would have been more reliable.
Fair Winds
Graeme
-
28th June 2013, 11:17 PM #7.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,807
-
29th June 2013, 02:00 AM #8China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
Did you complete the renovation yourself if not the builder is liable and has to replace it !!!
Similar Threads
-
The Grey Seal Huon Seal
By dopeydriver in forum BOAT BUILDING / REPAIRINGReplies: 429Last Post: 21st April 2012, 12:31 AM -
Timber swelling on new pool deck
By around360 in forum WOODWORK - GENERALReplies: 11Last Post: 29th November 2009, 02:57 PM -
Air tight MDf cabinet. How to seal the doors!
By supergrame in forum WOODWORK - GENERALReplies: 13Last Post: 4th July 2009, 12:04 PM -
to seal or not to seal? timber window frames prior to puttying
By bljones in forum WOODWORK - GENERALReplies: 2Last Post: 20th May 2009, 10:52 PM