Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 12 of 12
  1. #1
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default Anyone made a pottery wheel

    Hi. Has anyone ever made a pottery wheel if so, care to share some details on what and how you made it.

    I’m mainly thinking of making a kick wheel (human powered) but may go electric If it’s simple enough.

    I’ve watched plenty of YouTube videos and googled the subject.

    Cheers
    Arron
    Apologies for unnoticed autocomplete errors.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many





     
  3. #2
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    4,470

    Default

    I made one for girlfriend 30 years ago there is nothing complicated about them, wheel mounted direct to a TEFC motor speed control or pulley, kick version would have a long shaft with bearing top and bottom and wheel at the bottom to kick

  4. #3
    Join Date
    Jul 2005
    Location
    Oberon, NSW
    Age
    63
    Posts
    13,354

    Default

    Back in the 70's our Woodwork class made several kick-wheels for the Art class.

    I don't rightly recall how the top bearing was set up, but I do remember that the bottom bearing was quite simple. Basically, a nut welded to a plate that was fixed in the middle of the bottom leg cross-brace. A bolt (probably 1/2 - 3/4" dia) was ground to have a pointed tip and screwed into the nut from underneath so the point extended sufficiently past the top of the nut for clearance. The fly-wheel assembly sat on this point, centered by a dimple in the end of the shaft.

    I remember it as I was quite impressed at how simple it was while being robust enough to carry the weight. (From memory the fly-wheel was several inches thick and quite a large diameter. Heavy enough that its' being "kicked off the pivot" wasn't a concern.)

    Since then I've built a few random devices, such as a treadle lathe, that have used the same bearing design.
    I may be weird, but I'm saving up to become eccentric.

    - Andy Mc

  5. #4
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    That’s a great simple solution Skew. How deep should the dimple on the shaft be? Do you think?
    Apologies for unnoticed autocomplete errors.

  6. #5
    Join Date
    Dec 2006
    Location
    East of Melbourne Aus.
    Age
    72
    Posts
    1,219

    Default

    I have built a few over the years, but only have a shop bought one at the moment. Mostly I have used a cone drive rubbing against a rubber ring sitting in a pulley wheel. I have the makings of a good big wheel at the moment sitting in a shed. It would be able to hold at least 60kilo of clay. 50mm shaft and 40mm wheel head. Big bearings. It depends on what sort of pots you want to build.
    I am learning, slowley.

  7. #6
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    Quote Originally Posted by Pagie View Post
    I have built a few over the years, but only have a shop bought one at the moment. Mostly I have used a cone drive rubbing against a rubber ring sitting in a pulley wheel. I have the makings of a good big wheel at the moment sitting in a shed. It would be able to hold at least 60kilo of clay. 50mm shaft and 40mm wheel head. Big bearings. It depends on what sort of pots you want to build.
    Only rather small stuff planned at the moment.
    Can you explain what is meant by a “cone drive rubbing against a rubber ring sitting in a pulley wheel” . Please
    Cheers
    Arron
    Apologies for unnoticed autocomplete errors.

  8. #7
    Join Date
    Dec 2006
    Location
    East of Melbourne Aus.
    Age
    72
    Posts
    1,219

    Default

    It is easy to build. you need to move the motor on a cradle up and down so a cone on the drive shaft rubs against a rubber ring on the main shaft. The cone gives you variable speed. We could not afford a veryiable speed motor.
    R3OpBAHITmKrhwy%lLISzw.jpg
    I am learning, slowley.

  9. #8
    Join Date
    Dec 2006
    Location
    East of Melbourne Aus.
    Age
    72
    Posts
    1,219

    Default

    Sorry for the bad drawing and the fact it is on it's side.
    I am learning, slowley.

  10. #9
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    Ok, so the motor is on a mount that is fixed at one end only - so the cone is kept against the V pulley by gravity.
    Plus the whole motor and it’s mount is able to be moved up and down vertically to give the variable speed.
    And the rubber provides a friction grip plus dampens noise.
    Is that all correct.

    I have a couple of old electic motor in 1/3 or 1/2 horsepower that should do the job. Where do you get a cone from, or should I expect to make one myself and is getting the speed range right just trial and error?

    Cheers and thanks
    Arron
    Apologies for unnoticed autocomplete errors.

  11. #10
    Join Date
    May 2003
    Location
    Central Coast, NSW
    Posts
    3,330

    Default

    For anyone with a knowledge of these things.

    I also have a rather new industrial sewing machine clutch motor which I recently swapped out for a servo motor.
    These motors are built to run 24x7 in an industrial environment. They run full speed all the time but don’t provide power till you press a pedal down, which engages a clutch. Would that be suitable ? I expect I could swap the foot pedal for a hand control, perhaps a lever with friction to make it stay where it is put?

    I was originally thinking of using a kick wheel as I didn’t want to deal with motors, but seeing the size of the kick wheels and thinking about my bad back I’m now thinking maybe a motor would be better.

    The motor with variable speed cone sounds attractive because I can use one of the daggy old motors I have, but the sewing machine clutch motor is attractive because it’s pretty much ready to go and I’m not good with anything engineering-oriented so may struggle to get the cone motor integrated.

    And to further complicate things the clutch motor is very heavy too so in my case that is a significant negative.

    Toss up between the three methods. Any input welcome.

    Cheers
    Arron
    Apologies for unnoticed autocomplete errors.

  12. #11
    Join Date
    Dec 2005
    Location
    South Australia
    Posts
    4,470

    Default

    Arron the clutch motor would d you would need to devise a method of holding the wheel at a selected speed, once you select yours speed you don't want is speeding up or slowing down if you can avoid it
    with the clutch motor a simple thumb screw arrangement on the pedal shaft would work, i.e. push the pedal to achieve the desired speed and lock with a thumb screw ( I hope that makes sense ) or replace the pedal and just use the haft as a push pull type set up.
    If you are concerned about overall weight mount the entire thing on locking casters.

  13. #12
    Join Date
    Dec 2006
    Location
    East of Melbourne Aus.
    Age
    72
    Posts
    1,219

    Default

    I have used a wooden cone for years without a problem. The motor needs to be held both ends but can be moved in an arc. In use you need to be able to stop or slow the speed of the wheel as you are working. Have a look at the Simon Leach kick wheel. Very heavy but very good control.
    I am learning, slowley.

Similar Threads

  1. Home made Wetstone system or CBN wheel??
    By artme in forum SHARPENING
    Replies: 25
    Last Post: 4th April 2015, 08:15 PM
  2. New pottery shed
    By Pagie in forum SMALL TIMBER MILLING
    Replies: 9
    Last Post: 5th June 2014, 09:07 AM
  3. Pottery Wheel needed
    By Pagie in forum POTTERY
    Replies: 5
    Last Post: 10th May 2014, 11:49 PM
  4. Pottery tools
    By Sawdust Maker in forum POTTERY
    Replies: 17
    Last Post: 5th November 2008, 04:29 PM
  5. Throwing sticks for pottery
    By dan_tom in forum POTTERY
    Replies: 8
    Last Post: 19th July 2006, 01:09 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •