Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Price for 6 saw blades
-
1st April 2017, 01:36 PM #1Intermediate Member
- Join Date
- May 2012
- Location
- Brisbane
- Posts
- 30
Price for 6 saw blades
Hi all,
i have 6 saw blades for sale on the Auction page. I'm asking $220 for them. I am not getting much interest in them and so i was wondering if i'm asking to much. What would be a reasonable price for the following saw blades...
1 X CMT 10inch ripping blade. 30mm arbor and 24 teeth.
1 X CMT 10inch Aluminuin Profile & Laminated Chipboard blade, 30mm arbor and 80 teeth.
1 X CMT 10inch Melamine & Fine Cut Off, 30mm arbor and 80 teeth
1 X (don't know the brand or type of blade) 10inch, 30mm arbor and 100 teeth.
1 X Elektra Beckum 10inch (don't know what type of blade it is), 30mm arbor and 60 teeth. It still has the wax on the teeth from when i had it sharpened.
1 X Vermont American 9 1/4 inch thin Kerf blade, 25mm arbor and 60 teeth.
I'm not sure what the grind type is on these blades.
5 out of the 6 are in good condition. Thanks very much fr your help.
-
1st April 2017 01:36 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
1st April 2017, 03:45 PM #2
Hi Steven
as you can see from my signature, I'm located in Canada. But this is my perspective.
I can buy a new Avanti (a Freud brand) 10" saw blade for about $15 from the local equivalent to Bunnings. Actually a 2 blade pack containing 1 x 60 tooth cross-cut, 1 x 24 tooth rip is advertised for $32. (A local tool store has a similar 2 blade pack for $20)
turning to your three CMT blades, in effect you are asking around $60 each for each of these blades. But what is the price for a new CMT blade in Australia? Carbatech seem to be asking around $75 to 85.
and whilst the blades might be in very good condition. They might equally need to be sharpened and not have much carbide left on them. But how do I know?
I hope the above is useful. It's not meant to be a criticism, just a perspective.regards from Alberta, Canada
ian
-
1st April 2017, 03:50 PM #3rrich Guest
A Yank here, so take what I say with a grain of salt.
I don't know what the standard arbor sizes are on international or metric tables saws. In our amateur saws most of our arbors are 5/8 inch or not quite 16MM. So in my shop the blades are worthless to me.
The CMT and Vermont American brands are known here in the US. I don't hear a lot about the CMT brand which is good and bad. If we don't hear much it means that nobody has an axe to grind and nobody is raving about the brand either. The Vermont American is not of the greatest quality and most serious woodworkers avoid the brand.
The tooth configurations of the blades that you have listed are not sufficient. The only blade that I am fairly certain of the tooth configuration is the ripping blade. (Raker teeth) But the bad news here is that unless one is planning to rip several hundred meters, no one is going to take the time and trouble to change the blade.
I'm not sure what a Aluminium Profile & Laminated Chipboard blade would be used for. They seem to be in opposite directions of usage.
The Melamine & Fine Cut Off again seems to be a conflict of terms especially with 80 teeth.
As for the money? I can't help with that as I'm too far away.
-
1st April 2017, 07:47 PM #4Intermediate Member
- Join Date
- May 2012
- Location
- Brisbane
- Posts
- 30
Thanks very much for your help!!!
-
1st April 2017, 10:10 PM #5Taking a break
- Join Date
- Aug 2008
- Location
- Melbourne
- Age
- 34
- Posts
- 6,127
Aluminium and laminates both use a Triple Chip grind. Aluminium blades should have a 0 degree rake, laminates are usually about 10 degrees but 0 will work as well.
Also no conflict for the second blade; high tooth count ATB is recommended for both, but if you don't have a scoring blade on your saw a triple chip is better for melamine.
Similar Threads
-
Retail price V's Wholesale price?
By corbs in forum WOODTURNING - PEN TURNINGReplies: 9Last Post: 30th July 2014, 10:55 PM -
meter cube price to board size price - conversion tool
By old_picker in forum TIMBERReplies: 7Last Post: 27th January 2013, 09:21 PM -
Ryobi Thicknesser blades blades
By kcam in forum GENERAL & SMALL MACHINERYReplies: 8Last Post: 30th September 2011, 08:03 PM -
High AUD = Price Drop on IBC Blades
By JimDavey in forum HAND TOOLS - UNPOWEREDReplies: 0Last Post: 6th May 2011, 07:32 AM -
Australian price Vs US price?
By corbs in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 14Last Post: 13th February 2010, 08:00 PM