Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Red Gum Slabs
-
23rd May 2010, 12:13 AM #1New Member
- Join Date
- May 2010
- Location
- North east vic australia
- Posts
- 3
Red Gum Slabs
Hi all
I'm new to forum. Would like to ask a few questions and get input.
I have some red gum slabs and am keen to getting them surfaced to sanding ready for sanding stage.
Is the wood wizz the way to go?
What would be the norm price for surfacing per metre?
Has anyone used a big drum type sander/ or would this just follow the contours and not bring it dead flat?
Has a home made setup with 2000 router and large bit been successful by anyone for multiples of slabs?
how soon after dressing would one want to seal them to stop them from twisting etc, would imagine ASAP? After sanding to finish Would a person have time to finish 3-4 coats on one side before turning to complete other, or is it an immediate process turn and do coats in rotation?
What products recommended for good natural finish?
I would be thankful for your input!
Thanks
Lazza.
https://www.woodworkforums.com/member...albums/redgum/
-
23rd May 2010 12:13 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd May 2010, 03:01 PM #2Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
G'day Lazz and welcome to the forums.
Can't help you with Wood Wizz costs, but i can sat they do a fabulous job.
Large drum sanders also do a wonderful job. I had some slabs done on a big industrial machine some years ago. Cost $100 just to start the machine. Had I have had other work to do it would have been really cheap.
I wouldn't consider any other means of sanding than these two
My advice is to seal the ends first and then get one good coat on either side as quicly as possible. You can do this by standng them on their edges.
Sanding betweeen coats is advisable.
Good luck.
-
23rd May 2010, 05:25 PM #3New Member
- Join Date
- May 2010
- Location
- North east vic australia
- Posts
- 3
Hi Artme,
Thanks for the promt reply and info,
Good idea to stand them on edge and coat 2 sides at once.
I am taking one next wkd to be wizzed as a bloke said he will do one for me as he very busy. I'm hoping some fella be happy to hire his machine and will look out for an industrial sander setup and hire it for a few hours in it's downtime.
I will indeed sand between coats.
Would the bark edge require same sealer as end grain or would you recommend other for this?
Thanks for your time,
Regards
Lazza.
-
23rd May 2010, 06:15 PM #4Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
By sealing the ends I should have said with the same finish you use for the top and bottom surfaces. Same goes for the edges.
I think you will be lucky if the bark stays on. Which brings me to asking if the slabs are well and truly seasoned.
-
23rd May 2010, 07:14 PM #5New Member
- Join Date
- May 2010
- Location
- North east vic australia
- Posts
- 3
Your right the bark has very little hope of remaining i will give it a light rub with a brass wire stripper and take it back to bare.
The slabs were stacked between gluts very well by the farmer in a 3 sided shed, covered with a canvas and have been lying there for over 2 1/2 years, the tree had been down over a decade in the paddock.
I dont have a moisture content measuring device but they appear to be fair dry and brittle to look at but this may mean nothing i guess.
Similar Threads
-
FREE SLABS - MELBOURNE - not beer slabs
By sailor in forum TIMBERReplies: 28Last Post: 11th July 2009, 10:17 AM