Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 11 of 11
-
5th June 2005, 03:24 PM #1
Dust maker
- Join Date
- Jan 2004
- Location
- Sunshine Coast. Qld
- Age
- 78
- Posts
- 356
Removing liquid nails, any suggestions
I have the oppotunity to acquire some recycled Tassie oak wall panneling.
The only problem is that it has globs of liquid lails where it was attached to the wall. Anyone have any sensible suggestions on how to remove this glue. :confused:
David
-
5th June 2005 03:24 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
5th June 2005, 05:51 PM #2
SENIOR MEMBER
- Join Date
- Jul 2002
- Location
- Albany WA
- Age
- 83
- Posts
- 749
http://paint-and-supplies.hardwarest...er-103697.aspx
I collected this site from a US BB. I have no idea if it works or whether it, or it's equivalent, is available in Oz.
Try your local paint store or builders hardware store.
It only takes one drink to get me loaded. Trouble is, I can't remember if it's the thirteenth or fourteenth.
-
5th June 2005, 05:55 PM #3
GOLD MEMBER
- Join Date
- May 2003
- Location
- Kuranda, paradise, North Qld
- Age
- 62
- Posts
- 5,639
David,
a sharp chisel will remove the bulk of it. If it's on the back of the panelling that's all you may need to do, unless both sides will be seen, in which case a bit of sanding will remove the rest.
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
5th June 2005, 06:09 PM #4
Senior Member
- Join Date
- Jun 2004
- Location
- Melbourne, South East Subs.
- Posts
- 395
I used a power plane to do exactly that job today, from the back of some used pine floorboards. Works fine.
Regards,
Rusty.The perfect is the enemy of the good.
-
5th June 2005, 06:48 PM #5
Registered
- Join Date
- Aug 2003
- Location
- .
- Posts
- 10,482
How come youve got to take all the fun out of life.....:confused:
Originally Posted by David L
Al
-
5th June 2005, 10:05 PM #6
Producer of fine shavings
- Join Date
- Oct 2004
- Location
- Melbourne
- Posts
- 945
Damn it, and I was about to suggest to run it over with your lawnmower... Originally Posted by David L
You can never have enough planes, that is why Mr Stanley invented the 1/2s
-
6th June 2005, 01:19 PM #7
Senior Member
- Join Date
- Apr 2003
- Posts
- 214
As one that has removed way more Con Ad than I would ever care to admit, I agree that this is the best method. Get your widest chisel out, get a low angle on the board, and hammer that chisel until it comes off. This will likely result in gouging some of the timber if you don't have a low enough angle. Originally Posted by journeyman Mick
In the beginning the Universe was created.
This has made a lot of people very angry and been widely regarded as a bad move.
- Douglas Adams
Guns are bad, mmmmkay.
-
6th June 2005, 02:23 PM #8
Senior Member
- Join Date
- Oct 2003
- Location
- Gold Coast,Australia
- Age
- 49
- Posts
- 350
i used a heatgun when i had to get a tile off of a brick wall, but you may issues with this method seeing the panelling is timber.
G
-
6th June 2005, 02:45 PM #9
GOLD MEMBER
- Join Date
- May 2003
- Location
- Kuranda, paradise, North Qld
- Age
- 62
- Posts
- 5,639
I thought they'd just use a chisel (or scalpel) :eek: Originally Posted by Groggy
Mick"If you need a machine today and don't buy it,
tomorrow you will have paid for it and not have it."
- Henry Ford 1938
-
6th June 2005, 04:53 PM #10
Super Moderator
Dodgy brother
- Join Date
- May 2004
- Location
- Pakenham, outer Melb SE suburb, Vic
- Age
- 54
- Posts
- 4,158
A scraper with a sharp hook could be the go after removing the bulk with a blade.
Cheers...........Sean, hooked on scrapers
The beatings will continue until morale improves.
-
7th June 2005, 10:44 AM #11
Dust maker
- Join Date
- Jan 2004
- Location
- Sunshine Coast. Qld
- Age
- 78
- Posts
- 356
Thanks everyone sounds like I should be able to do it whithout to mutch sweat.
David
Reply With Quote
