Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
-
13th June 2014, 08:18 PM #1GOLD MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Age
- 37
- Posts
- 2,711
Repairing scratches in hardwood floors
Hi all,
I have solid Jarrah floorboards throughout my house and was wondering how I can go about fixing scratches? The wife was vacuuming the other day and there must have been a little bit of a build up of dust under the vacuum and managed to scratch the floor (around 3 metres long). The scratch is very fine i.e you can not feel it if you run your finger accross it. The floors were sanded last August with 2 coats of polyurethane so the scratch stands out.
I have considered wax sticks however I'm just concerned that it may not blend in as well. Would buffing be an option?
Thanks for any help.
Cheers,
Andy.
-
13th June 2014 08:18 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
13th June 2014, 09:22 PM #2SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- Gold Coast
- Age
- 63
- Posts
- 847
Are the floorboards scratched or is it just the poly ?
I’ve used acetone on small fine scratches on a satin finish poly-ed tabletop. I was expecting it to fail and the patches to stand out but it it’s hardly noticeable.
-
13th June 2014, 09:33 PM #3GOLD MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Age
- 37
- Posts
- 2,711
To be honest I'm not sure if it's the poly or the floor .
What was your process for applying the acetone?
Thanks.
-
13th June 2014, 10:01 PM #4SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- Gold Coast
- Age
- 63
- Posts
- 847
I used a quick light circular motion with a soft cotton cloth balled up to maybe a third of fist size. Wet but not dripping wet. Similar to how I usually apply stains and shellac.
Afterwards I buffed it “dry” using the same type of action and a dry cotton cloth. Not sure if it really needed that but I thought it best.
I actually started on a patch that was whitened and heat affected. It was smack in the middle so I had nothing to lose. That seems to work so I moved on to the scratches. The owner tells me some smallish white patches reappeared in the heat affected area after a day or so but the scratches are not noticeable.
-
13th June 2014, 10:51 PM #5GOLD MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Age
- 37
- Posts
- 2,711
Thanks Dabbler. So no preparation on the wood before using the acetone? Just straight on then buff off?
-
13th June 2014, 11:03 PM #6SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- Gold Coast
- Age
- 63
- Posts
- 847
No preparation. If it’s poly then acetone will move it.
If the scratches are deeper than the poly and into the timber then acetone itself won’t solve the problem. If you need to remove a patch of poly to get to the timber, I think it will always look patchy once you fix and re-coat a section.
If you are lucky like I was, the poly is the only affected bit and maybe a fix is possible without much drama.
-
15th June 2014, 07:39 PM #7GOLD MEMBER
- Join Date
- Mar 2009
- Location
- Sydney
- Age
- 37
- Posts
- 2,711
Will the acetone completely remove the poly? Just weighing up how it will look if I need to refinish the scratched area.
Thanks.
-
15th June 2014, 07:49 PM #8SENIOR MEMBER
- Join Date
- Dec 2007
- Location
- Gold Coast
- Age
- 63
- Posts
- 847
Yes eventually. That’s why I think deep scratches into the timber won’t be fixed this way as it will probably look patchy when re-coated.
I suppose your scratches are all in exposed areas which means it might be a gamble.
I am surprised no one else has come along with their own experiences.
-
18th June 2014, 03:17 AM #9
Good Morning Andy
Dabbler has given you good advice if the scratch is purely in the poly - the acetone will dissolve the poly, then it will evaporate and the poly will harden again. The trick is to remove the scratch, but not rub too hard and remove all the polyurethane.
if you get up real close - 300 mm - with a strong light then you should be able to see how deep the scratch is.
However, if the scratch is into the Jarrah then I am afraid there is little that can be done short of redoing the entire floor - any patch-up will be much more visible than the original scratch.
fair winds
Graeme
Similar Threads
-
Protecting timber floors from chair scratches
By custos in forum HINTS & TIPSReplies: 14Last Post: 28th May 2019, 02:42 AM -
Cypress Pine Floors - Dream of natural, matt floors but what to use??
By jessytiger in forum FINISHINGReplies: 1Last Post: 6th May 2011, 10:24 PM -
Scratches on hardwood workbench
By Wongo in forum THE WORK BENCHReplies: 41Last Post: 6th September 2008, 06:14 PM -
Finishing Hardwood floors with a spray gun?
By dgreene in forum FINISHINGReplies: 4Last Post: 11th June 2005, 04:15 PM