Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 19
Thread: One-way screw removal?
-
11th April 2008, 12:39 PM #1
One-way screw removal?
Does anyone know of a way or have a tool that can remove those safety/one-way screws. I have a few rusted window locks i need to remove and have just found out they are installed with these screws. I have seen pics on the net of tools but i cant find any in Australia...
Screw Example
Removal Tool
nesbit
-
11th April 2008 12:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th April 2008, 02:23 PM #2SENIOR MEMBER
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 455
had no idea you could get removal tools for these screws? where do you get em.
Sorry dont know where to buy the screws separately of hand.
Regards
Steve
-
11th April 2008, 02:25 PM #3
-
11th April 2008, 02:27 PM #4
-
11th April 2008, 05:31 PM #5Senior Member
- Join Date
- Feb 2008
- Location
- Kingscliff NSW
- Posts
- 327
Drill them out is probally your best chance,careful they are hardened steel.
-
11th April 2008, 07:54 PM #6
How about using ane Ezy-Out bit?
WolffieEvery day is better than yesterday
Cheers
SAISAY
-
11th April 2008, 08:34 PM #7SENIOR MEMBER
- Join Date
- Oct 2001
- Location
- ACT
- Posts
- 455
I imagine the tool pictured above is only good to screw them in by the look of it?
Why not just grind a slot with a dremel and just used an ordinary screwdriver to rmove them
-
11th April 2008, 08:51 PM #8
-
11th April 2008, 09:32 PM #9
I can't see how that can be the removal tool. The screw heads have a slope on the anti-clockwise edge which is not supposed to allow any sort of tool or blade to be able to get purchase on the screw to remove it. That'd be why they're called "one way screws".
However, if you can grind this slope to a 90* edge, then a blade screwdriver should be able to remove them.Too many projects, so little time, even less money!Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds! Doing work around the home? Wander over to our sister site, Renovate Forum, for all your renovation queries.
-
11th April 2008, 09:53 PM #10Senior Member
- Join Date
- Jun 2005
- Location
- sydney
- Posts
- 137
I have sucesfully removed these by grinding a screwdriver slot in them then using a flat blade to remove the screw, they then need to be replaced
Doug
-
11th April 2008, 09:54 PM #11SENIOR MEMBER
- Join Date
- Aug 2005
- Location
- Victoria
- Posts
- 664
-
11th April 2008, 10:10 PM #12GOLD MEMBER
- Join Date
- Aug 2005
- Location
- Queensland
- Posts
- 2,947
As the others have said, Dremel and then reverse them after cutting the slot. Not sure why they are used as they only seem to upset the honest people and do not bother the Crims at all - they just smash the window and don't bother with removal - they remove the glass and then your gear.
-
11th April 2008, 10:24 PM #13
But someone made a lot of money selling them, didn't they...
Cheers, Richard
"... work to a standard rather than a deadline ..." Ticky, forum member.
-
11th April 2008, 10:27 PM #14China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
I found out years ago the best way to remove them is to throw them out before using and replace with a conventional screw of some type, otherwise as said above Dremel
-
11th April 2008, 10:28 PM #15
The only way I could remove such a couple of years ago was to cut through the whole lock with an angle grinder
needless to say the lock was not much good but I got them off
tried drilling - life's too short
now I have a dremel I'd try that approach
good luck
Similar Threads
-
Wax removal
By Peter_I in forum WOODWORK PICSReplies: 1Last Post: 25th August 2006, 04:31 PM -
screw job
By JimboJ in forum WOODWORK - GENERALReplies: 5Last Post: 7th August 2006, 01:12 PM -
What is your favorite screw?
By echnidna in forum WOODWORK - GENERALReplies: 44Last Post: 13th December 2004, 09:59 AM -
Glue or Screw
By himzol in forum GLUEReplies: 7Last Post: 6th October 2004, 10:25 AM