Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: Shelf Unit HELP
-
9th February 2010, 04:53 PM #1New Member
- Join Date
- Feb 2010
- Location
- Melbourne, Vic, Aust
- Posts
- 3
Shelf Unit HELP
Gday all,
Im going to make a shelving unit for a friend and theres one thing i cant figure out how to do. Now, I am no pro when it comes to woodworking, some may even say beginner, so I really dont know what the best way would be to approch the situation.
The problem:
Now, if you have a quick look at the following pics done with GoogleSketchUp 6 you will get a basic idea of what Im hoping to make.
So,
How would I go about attaching the legs/vertical supports to the shelves themselves?
The poles will have a 30mm diameter and will go through snug holes drilled in each shelf.
Well I hope you understand what I mean because I really dont know how to do this...without sacrificing aesthetics anyway.
Sorry if it is a fairly obvious solution but like I said, I am quite new at this.
Any advice would be much appreciated.
Thanks
Matt
-
9th February 2010 04:53 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
9th February 2010, 10:03 PM #2" making wood good"
- Join Date
- May 2008
- Location
- Hervey Bay QLD
- Posts
- 319
You Could use a threaded rod to run through the pipe and have a large washer with a dome nut at each end to hold the shelfs together??
regards chowcini
-
10th February 2010, 01:37 PM #3New Member
- Join Date
- Feb 2010
- Location
- Melbourne, Vic, Aust
- Posts
- 3
how would that work? how would that secure the middle shelves onto the uprights? and anyways, the uprights are going to be solid, not hollow so tis not really an option....
cheers anyway
-
10th February 2010, 05:22 PM #4Novice
- Join Date
- Apr 2009
- Location
- Adelaide
- Posts
- 12
My first thought would be to have the 'poles'/'supports' cut at each shelf. You'd then cut a few mm into the shelf at the same diameter as the pole.
From here, you fit your pole into the hole glue / screw etc. For the top of the shelf, do the same thing. Few mm into it, and pop a 'cap' onto it.
It's not technically going /through/ the shelf, but it creates the illusion of it.
-
10th February 2010, 05:39 PM #5GOLD MEMBER
- Join Date
- Aug 2007
- Location
- Brisbane
- Posts
- 1,156
My idea was on similar lines, but with holes that are smaller than the diameter of the supports and make the supports slightly smaller in diameter to go into these holes. Each support would have to extend a maximum of half way into the shelf for that to work.
Another idea would be to make the shelf thick enough to take a dowel or a screw with a plug covering it. You would place the shelf correctly, drill for your dowel or screw and then fix it in place. Only problem with that (apart from IMO not looking as good) is that the screw or dowel would then be holding the weight of the shelf - not the support.
PeterThe other day I described to my daughter how to find something in the garage by saying "It's right near my big saw". A few minutes later she came back to ask: "Do you mean the black one, the green one, or the blue one?".
-
10th February 2010, 06:37 PM #6
You will need 16 threaded inserts and 16 bolts/screws that fit the thread inside the inserts.
Then you cut the all the posts to the same length plus the short lengths that fit on top of the offset shelves and drill a hole in each end of the posts.
I see you use sketch-up.
I was trying to show you how but, unfortunately,you have submitted a jpg file instead of a sketch-up model so I couldn't work on it.
Post your sketch-up model here and I will see what I can do for you.
It appears your shelves are only 100 mm deep?????
That is goint to toppleover.
Cheers
WolffieEvery day is better than yesterday
Cheers
SAISAY
-
11th February 2010, 04:36 AM #7New Member
- Join Date
- Feb 2010
- Location
- Melbourne, Vic, Aust
- Posts
- 3
Yea sorry mate...was not sure how to post the sketch-up model and to be honest Im still not sure. If I figure out how to I will post it.
It appears your shelves are only 100 mm deep?????
That is goin[g] to toppleover
You will need 16 threaded inserts and 16 bolts/screws that fit the thread inside the inserts.
Then you cut the all the posts to the same length plus the short lengths that fit on top of the offset shelves and drill a hole in each end of the posts.
I appreciate the advice
Matt
Similar Threads
-
Help adjusting shelf in entertainment unit
By tonydav in forum WOODWORK - GENERALReplies: 5Last Post: 10th August 2009, 12:11 PM -
REALLY cheap shelf unit...
By Skew ChiDAMN!! in forum WOODWORK - GENERALReplies: 14Last Post: 11th January 2008, 11:27 AM -
Camphor Laurel Kitchen Dresser Top Shelf Unit
By RufflyRustic in forum WOODWORK PICSReplies: 20Last Post: 25th October 2005, 02:31 PM -
A basic shelf unit
By Craig Gordon in forum WOODWORK PICSReplies: 3Last Post: 20th September 2004, 01:12 PM